How To Winterize Above Ground Pool With Sand Filter: The Complete Step-by-Step Guide

How To Winterize Above Ground Pool With Sand Filter: The Complete Step-by-Step Guide

Gas Heater for Inground Pools with Sand Filter and Salt Generator | How ...

Winterizing an above-ground pool equipped with a sand filter requires systematically lowering water chemistry, draining internal pump components, and thoroughly backwashing and winterizing the sand bed to prevent freeze-thaw damage. Completing this process before freezing temperatures arrive protects your pool walls, liner, and filtration equipment from cracking under ice expansion.


Pre-Operation & Equipment Checklist

Proper preparation prevents costly liner tears, PVC pipe cracking, and winter algae blooms. Before starting the winterization process, ensure you have all necessary materials staged near your equipment pad. The entire operation typically takes between two to four hours, depending on pool volume and whether you remove top rails or decks.



  • Essential Equipment & Materials: Heavy-duty winter pool cover, air pillow (for under-cover ice compensation), winterizing chemical kit (alkalinity increaser, pH balancer, winter algaecide, non-chlorine shock), pool antifreeze (propylene glycol, never automotive ethylene glycol), gizmo winterizing plugs, Teflon tape, pliers, garden hose, shop vacuum, and backwash hose.
  • Prerequisite Standards: Balance water chemistry at least 48 to 72 hours before closing. Total alkalinity should sit between 80 and 120 ppm, pH between 7.2 and 7.6, and calcium hardness between 175 and 250 ppm. Ensure free chlorine drops below 3.0 ppm before adding winter algaecide to prevent liner bleaching and chemical binding.
  • Time & Cost Benchmarks: Expect a budget of $50 to $150 for chemical kits, plugs, and antifreeze if starting from scratch. Allocate a dedicated afternoon to guarantee each step is executed without rushing.

Step-by-Step Above Ground Pool Winterization Workflow



Step 1: Deep Clean and Balance Water Chemistry



  1. Remove all ladders, leaf skimmers, and pool toys from the water to prevent rust staining and liner damage over the winter.
  2. Vacuum the pool floor thoroughly to eliminate organic debris that could decay, stain the liner, or consume winter algaecide reserves.
  3. Shock the pool water with a non-chlorine shock or a specialized winter chlorine shock, running the filtration system continuously for 24 hours to ensure thorough mixing.
  4. Add a long-lasting, copper-free winter algaecide directly to the water surface while the pump runs, preventing spring algae colonization.


Step 2: Backwash and Rinse the Sand Filter



  1. Turn off the pool pump at the breaker to ensure electrical safety.
  2. Rotate the multi-port valve handle to the Backwash position, secure it with the locking pin or clamp, and run the pump for 3 to 5 minutes until the sight glass runs completely clear.
  3. Turn off the pump again, move the multi-port valve to the Rinse position, and run the system for 60 seconds to settle the sand bed.
  4. Turn off the pump, rotate the valve to the Winter (or Drain) position, and disconnect the drain plug at the bottom of the sand filter tank to let all trapped water empty out completely.

Warning: Never use automotive antifreeze in your pool plumbing or filter. Automotive ethylene glycol is toxic to pets and wildlife and can degrade pool plastics and vinyl liners. Always use certified, non-toxic propylene glycol pool antifreeze.



Step 3: Lower Water Level and Drain Plumbing Lines



  1. Lower the pool water level to a safe point depending on your pool type and winter cover instructions, typically 4 to 6 inches below the skimmer return jet or skimmer mouth. Use a submersible pump or set your multi-port valve to the Waste position if your local wastewater codes allow.
  2. Disconnect the flexible hoses or PVC hard piping running between the skimmer, pump, and sand filter.
  3. Use a shop vacuum on the blower setting to push any residual water out of the return lines and underground plumbing runs.
  4. Pour a cup of pool antifreeze into the return line, then immediately thread a threaded winter plug or expansion plug into the return jet from inside the pool to seal it tightly.


Step 4: Winterize the Pump and Sand Filter Tank



  1. Unscrew the drain plugs located at the bottom of the pool pump housing and hair-and-lint strainer pot. Store these plugs inside the pump basket so they do not get lost over the winter.
  2. Remove the pressure gauge from the top of the multi-port valve and store it indoors to protect the delicate internal movement from freezing temperatures.
  3. Leave the multi-port valve handle positioned midway between settings (such as between Winter and Filter) to prevent internal gasket compression and tension degradation during freezing weather.
  4. Disconnect the pump and motor assembly entirely if you live in a region with hard, prolonged freezes, and store the unit in a dry garage or shed.


Step 5: Install the Skimmer Guard and Winter Cover



  1. Insert a skimmer gizmo (an expansion plug with a hollow cavity) into the skimmer throat to absorb ice expansion pressure and prevent the plastic skimmer housing from splitting.
  2. Place an inflated air pillow in the exact center of the pool surface, securing it with nylon cord tied to the pool top rails to relieve ice pressure against the pool walls.
  3. Drape the heavy-duty winter cover over the pool, pulling the cable taut through the eyelets and cranking the metal winch tight.
  4. Secure the perimeter of the cover with wall clips or water tubes if high winds are common in your region, preventing wind shear from lifting the cover.

How To Winterize A Coleman Above Ground Pool With Windows at Jennifer ...

How To Winterize A Coleman Above Ground Pool With Windows at Jennifer ...

Sand Filter Winterization Parameters Comparison



Component Action Required Storage Location Protection Material
Sand Filter Tank Drain via bottom plug Outdoors (covered) Non-toxic antifreeze / Valve open
Multi-Port Valve Set handle midway Outdoors (attached) Pressure gauge removed
Pool Pump Drain and disconnect Indoors / Shed Sealed dry environment
Return Lines Blow out and plug In-place (sealed) Expansion plug + Antifreeze

Common Site Failures & Field Fixes



  • Root Cause: Water left inside the sand filter tank expands during a hard freeze, cracking the fiberglass or structural plastic body.

    • Actionable Fix: Always remove the bottom drain plug immediately after backwashing. Leave the plug out all winter, and tilt the tank slightly if needed to guarantee complete drainage.
  • Root Cause: Groundwater or rain infiltrates the lowered pool, raising the water level back up into the skimmer housing and causing freeze damage.

    • Actionable Fix: Check your pool cover periodically throughout the winter. Use a cover pump to siphon off accumulated rain and melting snow before water levels reach the skimmer mouth.
  • Root Cause: Spring reveals severe green water and organic staining despite winterization efforts.

    • Actionable Fix: The algaecide dose was likely too low or applied too late. Ensure winter shock and algaecide are added on the exact same day, and apply a secondary booster dose of algaecide two weeks before anticipated spring opening.

Frequently Asked Questions



Should I change the sand in my filter before winterizing?

It is generally better to replace filter sand in the spring rather than the fall. Changing sand in the spring ensures you start the active swim season with fresh media that has not been sitting stagnant with trapped organic matter and oils all winter. However, if your sand is older than five years and severely channeled, replacing it in autumn is acceptable as long as you thoroughly dry and drain the tank.



Do I need to bring my sand filter inside for the winter?

No, sand filter tanks are rated for outdoor winter storage as long as all water is completely drained from the system. The multi-port valve pressure gauge and pool pump motor are the components most vulnerable to freeze damage and should be stored indoors. Leave the filter tank drain plug open and cover the motor pad with a breathable tarp.



Can I leave my above-ground pool completely full of water for the winter?

Leaving the pool full without lowering the water level risks damaging the skimmer, return fittings, and top rails when ice forms and expands. You must lower the water level below the skimmer return line and plug all openings to ensure a safe freezing buffer zone. Never drain an above-ground pool entirely, as hydrostatic pressure from surrounding soil can cause the vinyl liner to shrink and the pool walls to collapse.



What is the purpose of the air pillow under the winter cover?

The air pillow acts as a shock absorber for ice expansion. When ice forms on the surface of the pool water, it exerts immense pressure outward against the pool walls. The air pillow compresses inward under this ice pressure, protecting your steel or resin pool walls from buckling or snapping under extreme weather conditions.

Protect Your Investment All Year Long

Properly winterizing your above-ground pool and sand filter guarantees a seamless, crystal-clear pool opening when warm weather returns. Take time to execute each drainage and chemical balancing step carefully to maximize the lifespan of your equipment.


Hayward Sand Filter For Above Ground Pool at Florence Parsons blog

Hayward Sand Filter For Above Ground Pool at Florence Parsons blog

Read also: Finding a sally beauty supply near me has unexpected rewards