How To Tell If Your Well Pump Is Bad: A Professional Diagnostic Guide

How To Tell If Your Well Pump Is Bad: A Professional Diagnostic Guide

Best Ways to Prevent Power Surges from Damaging Your Well Pump

Diagnosing a failing well pump requires systematically evaluating electrical continuity, pressure switch performance, and water delivery consistency against standard operating thresholds. By tracking pressure tank drawdown cycles, checking amperage draw at the control box, and inspecting water clarity, you can pinpoint whether the issue stems from the pump motor, check valve, or pressure switch before initiating costly repairs.


Essential Diagnostic Preparation and Equipment

Diagnosing a submersible or jet well pump requires specific electrical safety gear and hydraulic testing instruments to prevent injury and avoid misdiagnosing secondary plumbing failures as pump burnout. Prior to opening any electrical enclosures or testing pressure lines, gather the proper tools and understand the baseline operational parameters of your water system. Most standard residential well systems operate within a 30 to 50 psi or 40 to 60 psi cut-in/cut-out range, and identifying deviations from these parameters forms the foundation of your troubleshooting protocol.



  • Essential Tools & Gear: Digital multimeter capable of measuring AC voltage and continuity, clamp meter for measuring running amperage, pipe wrenches, insulated screwdrivers, and a standard pressure gauge with a hose bib attachment.
  • Safety & Standards Compliance: Personal protective equipment including safety glasses and rubber-soled shoes; always shut off the main power breaker to the well pump at the service panel before removing control box covers or pressure switch housings.
  • Time & Cost Benchmarks: Initial diagnostic checks require approximately 45 to 90 minutes; professional replacement of a failed submersible pump typically ranges from 1,500 to 3,500 dollars depending on well depth.

Step-by-Step Well Pump Diagnostic Workflow



Step 1: Inspect the Pressure Switch and Electrical Power Supply

Begin your diagnostic process at the pressure switch, which acts as the neurological center of your well system. Remove the plastic cover of the pressure switch and inspect the contact points for pitting, burning, or insect debris that could prevent electrical closure. Use your multimeter to verify that line voltage matches the pump motor requirements (typically 230V or 115V) when the system calls for water. If power flows into the switch but fails to exit toward the pump when pressure drops below the cut-in threshold, the switch contacts are likely fused or failing.

Warning: Line voltage inside the pressure switch enclosure is lethal. Never touch exposed terminals with bare hands, and ensure the main breaker is locked out if you need to clean or replace switch components.



Step 2: Evaluate Pressure Tank Drawdown and Water Cycling

A rapidly cycling pump—turning on and off every few seconds while a faucet is running—often mimics pump failure but actually indicates a water-logged pressure tank or a ruptured internal bladder. Turn off the power to the pump, drain the pressure tank completely via a hose bib, and check the Schrader valve with a tire pressure gauge. The air pressure inside the tank should measure exactly 2 psi below your pressure switch cut-in setting (e.g., 28 psi for a 30-50 switch). If water sprays out of the Schrader valve or the tank fails to hold air, the bladder has failed, forcing the pump to short-cycle and overheat.



Step 3: Monitor Water Flow Rate and Spitting Faucets

Observe the behavior of water streaming from your highest and furthest fixtures. Sputtering faucets, air bursts, or surging water pressure usually indicate that the pump is drawing air because the water table has dropped, the drop pipe has a crack, or the foot valve/check valve is failing and allowing water to drain back into the well. If the pump runs continuously without ever shutting off, yet produces a weak trickle or no water at all, the impeller may be stripped, or the drop pipe has disconnected entirely underground.

Pro-Tip: If your pump runs continuously without building pressure, immediately shut it off at the breaker. Running a submersible pump dry for even a few minutes can melt the plastic impellers or burn out the hermetically sealed motor windings.



Step 4: Measure Amperage Draw at the Control Box

If your system features a surface-mounted control box (common for 3-wire 230V submersible pumps), use a clamp meter to measure the running amperage on the red, yellow, and black motor leads while the pump is operating. Compare your readings against the Service Factor Amps (SFA) listed on the motor data plate or pump specification sheet. Amperage significantly higher than the rated SFA indicates a locked rotor, winding short, or failing capacitor, while zero amperage draw points to a severed power cable, tripped thermal overload, or burnt-out control box relay.


Well System Component Performance Comparison



Component Normal Operating Parameter Primary Failure Symptom Diagnostic Verification Method
Pressure Switch 30-50 or 40-60 psi range Pump fails to start or runs continuously Multimeter continuity test across closed contacts
Pressure Tank Air charge 2 psi below cut-in Rapid short-cycling of the pump motor Schrader valve check and bladder inspection
Check Valve Holds prime and column pressure Water drains back; pump loses prime Pressure gauge drop test over 30 minutes
Pump Motor Within Service Factor Amps (SFA) Tripping breakers or humming without turning Clamp meter amperage draw comparison

Common Well Pump Field Failures and Solutions



  • Root Cause: Failed Control Box Capacitors. Power surges or lightning strikes frequently fry the start or run capacitors located inside the external control box.

    • Actionable Fix: Inspect the capacitor for bulging casing, oil leaks, or a burnt smell. Replace the component with an exact microfarad (MFD) and voltage match to restore motor startup capability.
  • Root Cause: Worn Check Valve Allowing Backflow. If the check valve fails, water rushes back down the well casing after every cycle, forcing the pump to re-prime constantly and causing water hammer.

    • Actionable Fix: Install an inline check valve above ground near the pressure tank, or pull the drop pipe assembly to replace a faulty sub-surface check valve or foot valve.
  • Root Cause: Clogged Well Screen or Sediment Buildup. Iron bacteria, sand, or mineral scale can choke the intake screen, starving the pump of water and causing cavitation.

    • Actionable Fix: Perform a well rehabilitation treatment using professional surging and chemical development, or pull the pump assembly to manually clean and flush the intake screen.

Frequently Asked Questions



How long does a typical well pump last?

Most standard submersible and jet well pumps last between 8 to 15 years depending on water chemistry, usage volume, and the frequency of motor starts. Hard water, high iron content, and frequent cycling due to an undersized pressure tank can shorten this operational lifespan significantly.



Why is my well pump running constantly?

A continuously running pump usually indicates a severe plumbing leak between the pump and the house, a broken drop pipe inside the well casing, a stuck pressure switch contact, or a pump that is worn out and can no longer generate enough hydraulic pressure to reach the cut-off threshold.



Can I replace a submersible well pump myself?

While surface jet pumps can be easily swapped out by a handy homeowner, replacing a submersible well pump requires specialized lifting equipment like a tripod and winch to pull heavy drop pipes out of deep boreholes. Improper handling can drop the entire pump assembly down the well, turning a DIY repair into an expensive recovery operation.



What causes cloudy or sputtering water from a well?

Sputtering faucets indicate air entering the pressure system, often caused by a low water table or a cracked drop pipe. Cloudy or sandy water usually points to a failing well screen, a pump hung too low in the bottom sediment, or seasonal fluctuations in the local aquifer.

Contact our certified master well technicians today to schedule a comprehensive diagnostic flow test or emergency pump replacement for your property.


How to Determine Flow Rate of Well Pump | 3 Easy Steps (2026)

How to Determine Flow Rate of Well Pump | 3 Easy Steps (2026)

Read also: Quick tips for troubleshooting your specific metro pcs login