How To Rig A Tube Lure Like A Professional Bass Angler

How To Rig A Tube Lure Like A Professional Bass Angler

Carp Fishing Rigging Accessories Thermo Tube 2.5 mm | Decathlon

Rigging a tube lure correctly requires threading a specialized jig head entirely inside the hollow soft plastic body while exposing the hook precisely through the crown, ensuring a balanced, gliding descent. Mastering this technique transforms a simple hollow-plastic cylinder into a strike-inducing imitation of a fleeing crayfish or dying baitfish.


Essential Gear, Tools, and Technical Benchmarks for Tube Fishing

Tube lures are hollow, soft-plastic cylinders molded with interior tentacles at one end and a sealed or semi-open nose at the other. Because the hook and weight must fit inside the body cavity, preparation and gear selection dictate whether the lure swims true or spirals erratically on the fall.



  • Essential Gear and Materials: Salt-impregnated or standard plastic tube lures (typically 3.5 to 4.5 inches), internal tube jig heads with round or insert-style lead weights matched to the hook gap, a bottle of cyanoacrylate (super) glue, a bait-rigging needle or toothpick (optional for stubborn noses), and fluorocarbon line ranging from 8 to 12 pounds test.
  • Prerequisites and Standards: Anglers must understand how to identify the belly versus the back of the tube (often indicated by salt distribution or a slit seam) and match the hook gap width to the inner diameter of the plastic cylinder to prevent tearing during insertion.
  • Budget and Duration Benchmarks: Initial setup costs average between twenty and forty dollars for a starter selection of heads and bags of tubes. Rigging an individual tube takes approximately 30 to 45 seconds once technique is established.

Step-by-Step Tube Lure Rigging and Insertion Workflow



Step 1: Inspect and Prepare the Tube Nose

Examine the nose cone of the tube lure to ensure the plastic membrane is clean and intact. If the manufacturer left the nose completely open, pinch the sides slightly to locate the center point.

Pro-Tip: If the nose lacks a pre-punched hole, use the point of your hook or a bait needle to create a small pilot hole dead center in the nose tip, which prevents the lead head from pushing the plastic off-center.



Step 2: Insert the Internal Jig Head

Take your specialized internal tube jig head—where the weight is molded directly onto the hook shank immediately below the eyelet—and align it with the pilot hole. Push the pointed end of the jig head straight into the nose of the tube, sliding the entire lead weight and hook eye up inside the hollow body cavity. Continue pushing until the eye of the jig head presses firmly against the interior top of the nose cone.

Warning: Do not force a jig head that is too wide for the tube diameter, as this stretches the plastic, thins the walls, and causes the lure to tear easily upon catching a fish or snagging structure.



Step 3: Pierce the Plastic to Expose the Hook Point

Feel through the soft plastic wall of the tube to locate the exact position of the hook eye. Slide the hook shank down slightly until the bend of the hook aligns with the dorsal side (top) of the lure. Push the hook point outward through the top wall of the tube, ensuring that you pierce cleanly through the plastic without catching the inner lining or skewing the alignment of the bait.



Step 4: Secure the Lure Position and Check Alignment

Pull the hook eye completely through the pierced hole so that only the eyelet and the knot-tying area remain exposed outside the plastic. Apply a single drop of cyanoacrylate glue between the lead head and the interior plastic nose, sliding the tube forward to lock it into place. Hang the rigged tube vertically by the line tie to verify that it hangs straight without twisting or curling.


How to Pick the Best Soft-Plastic Lures for Crappie Fishing - Realtree Camo

How to Pick the Best Soft-Plastic Lures for Crappie Fishing - Realtree Camo

Technical Comparison of Tube Rigging Methods and Applications



Rigging Method Optimal Water Depth Primary Target Species Fall Rate & Action
Internal Jig Head 5 to 30 Feet Largemouth, Smallmouth, Spotted Bass Spiral glide; mimics dying baitfish
Texas Rig (Bullet Weight) 1 to 15 Feet Heavy Cover, Brush Piles, Weedlines Fast vertical drop; weedless presentation
Drop Shot Rig 20 to 50 Feet Deep Structure, Suspended Smallmouth Horizontal hover; subtle quiver
Open Jig Head ( exposed hook) Open Water, Rock Piles Smallmouth Bass, Walleye Natural swimming motion; high hook-up ratio

Troubleshooting Common Tube Rigging Failures



  • Symptom: The tube spirals violently or tacks sideways on the fall instead of gliding straight down.

    • Root Cause: The hook point exited the body off-center, or the jig head is wedged crookedly inside the cavity.
    • Actionable Fix: Remove the hook, re-center the jig head within the tube, and ensure the hook point pierces the exact dorsal centerline of the plastic cylinder.
  • Symptom: The plastic tube slides down the hook shank during a cast, bunching up near the bend.

    • Root Cause: Failure to secure the nose of the tube to the lead head using glue or a built-in wire keeper.
    • Actionable Fix: Use a drop of instant adhesive between the lead collar and the inner plastic wall, or switch to a jig head featuring a barbed collar.
  • Symptom: Frequent missed hooksets when fish bite.

    • Root Cause: The hook gap is buried too deeply within the plastic walls, or the plastic is too thick to compress upon striking.
    • Actionable Fix: Push the hook point out slightly further so more of the gap is exposed, or trim the plastic around the hook exit hole with scissors to reduce resistance.

Frequently Asked Questions



How do I know which size jig head to use inside a tube lure?

Match the weight of the jig head to your fishing depth and current speed, typically ranging from 1/8 ounce for shallow finesse applications up to 1/2 ounce for deep-water smallmouth fishing. The width of the jig head must match the inner diameter of the tube without over-stretching the plastic walls.



Should I use exposed hook or weedless rigging for tubes?

Use an internal jig head with an exposed hook when fishing over clean gravel, sand, or rock piles where snagging is minimal to maximize hook-up ratios. Switch to a Texas-rigged setup with a worm hook and bullet weight when targeting heavy brush, timber, or dense aquatic vegetation.



Can I reuse a tube lure after catching a fish?

Yes, but soft plastic tears easily around the hook exit hole after multiple fish catches or snags. Repair minor tears with soft plastic glue, or slide the tube down slightly and re-pierce a fresh section of plastic if the nose is severely stretched out.



What is the best rod and reel setup for fishing rigged tubes?

A 7-foot medium-heavy spinning rod paired with a 2500-series reel spooled with 10-pound braid and an 8- to 10-pound fluorocarbon leader provides the ideal balance of casting distance, sensitivity, and hook-setting power.

Elevate your finesse fishing game by stocking your tackle box with premium tube lures and matched jig heads designed for maximum underwater action.


Red October Baits 10" Monster Tube Rigs - Team Rhino Outdoors LLC

Red October Baits 10" Monster Tube Rigs - Team Rhino Outdoors LLC

Read also: How to Obtain Official Alameda County Birth Records