How To Reset Oil Life On 2014 Jeep Grand Cherokee

How To Reset Oil Life On 2014 Jeep Grand Cherokee

2014-2021 Jeep Grand Cherokee Generation 5 T-Style Radio - LinksWell, Inc.

Resetting the oil life monitor on a 2014 Jeep Grand Cherokee requires navigating the Electronic Vehicle Information Center (EVIC) or the 8.4-inch Uconnect touchscreen using the steering wheel control pads. Completing this procedure ensures your oil change interval accurately recalibrates from zero back to one hundred percent after an oil and filter service.


Pre-Procedure Planning and Vehicle Readiness

Before initiating the oil life reset sequence on your 2014 Jeep Grand Cherokee, certain cabin conditions and operational parameters must be met. This procedure does not require specialized OBD-II diagnostic scanners, as it utilizes the factory instrument cluster menu system. However, attempting the reset without following the correct ignition sequence will result in menu lockouts or a failure to save the new baseline percentage.



  • Essential Gear and Interface Tools: No tools are required, though a functioning electronic key fob and a healthy 12-volt starting battery are mandatory to maintain uninterrupted vehicle ignition modes.
  • Mandatory Prerequisite Knowledge: You must identify whether your specific 2014 trim level features the standard Electronic Vehicle Information Center (EVIC) with a 3.5-inch instrument cluster display or the upgraded 7.0-inch multiview cluster screen, as button navigations vary slightly by display package.
  • Estimated Duration and Budget Benchmarks: The physical reset procedure takes less than two minutes and costs nothing when performed independently following a standard fluid change service utilizing manufacturer-specified oil grades (such as 5W-20 for the 3.6L Pentastar V6 or 0W-40 for the 6.4L SRT V8).

Step-by-Step Oil Life Reset Procedure



Step 1: Engage the Ignition to the RUN Position Without Starting the Engine

Sit inside the driver seat and ensure all doors are fully closed. Press the ENGINE START/STOP button once without depressing the brake pedal. This action shifts the vehicle electrical architecture into the RUN/ON mode, illuminating the instrument cluster and powering the accessory networks while leaving the fuel injectors and starter motor disengaged.

Warning: Do not depress the brake pedal during this step. Starting the internal combustion engine complicates navigation through the diagnostic instrument cluster settings menu.



Step 2: Access the Vehicle Information Sub-Menu

Locate the directional arrow pads on the left-hand spoke of your steering wheel. Use the down arrow button to scroll through the primary instrument cluster menu options until you highlight the screen labeled Vehicle Info.



Step 3: Navigate to the Oil Life Percentage Metric

Once the Vehicle Info screen is active, use the right or left directional arrows on the same steering wheel control pad to cycle through the specific sub-menus. Stop when the display presents the Oil Life reading, which shows your current remaining engine oil degradation percentage and operating threshold.



Step 4: Execute the Reset Command via Steering Wheel Controls

Press and hold the OK button located directly in the center of the left-hand steering wheel directional pad. Maintain continuous pressure on the OK button for approximately three to five seconds. Watch the instrument cluster display update dynamically as the percentage rolls upward from its depleted state to 100%.

Pro-Tip: If the oil life indicator refuses to reset, release the button, cycle the ignition back to the OFF position, open and close the driver door to reset the body control module, and repeat the sequence from Step 1.


Used 2014 Jeep Grand Cherokee Altitude for Sale Near Me | Cars.com

Used 2014 Jeep Grand Cherokee Altitude for Sale Near Me | Cars.com

2014 Jeep Grand Cherokee Engine Oil Specifications and Capacities



Engine Option Recommended Oil Viscosity Oil Capacity with Filter Factory Change Interval Guideline
3.6L Pentastar V6 API Certified SAE 5W-20 6.0 Quarts (5.7 Liters) Up to 10,000 miles or 12 months
5.7L HEMI V8 API Certified SAE 5W-20 7.0 Quarts (6.6 Liters) Up to 10,000 miles or 12 months
3.0L EcoDiesel V6 ACEA C3 / API CJ-4 5W-30 8.0 Quarts (7.5 Liters) Up to 10,000 miles or 12 months
6.4L SRT HEMI V8 MS-12633 / SAE 0W-40 7.0 Quarts (6.6 Liters) Up to 6,000 miles or 6 months

Common Reset Failures and Field Fixes



Scenario A: Oil Life Indicator Fails to Advance to 100 Percent



  • Root Cause: The ignition was cycled into the accessory-only position instead of the full RUN position, denying the Powertrain Control Module (PCM) the proper system handshake required to overwrite memory registers.
  • Actionable Fix: Press the start button a second time without touching the brake pedal to verify the instrument cluster indicators and warning lights are fully illuminated, then repeat the button-hold sequence.


Scenario B: Menu Navigation Lacks the Vehicle Info Screen



  • Root Cause: The vehicle software version on early 2014 models may have uncorrected firmware bugs, or the instrument cluster is stuck in a customized user profile view.
  • Actionable Fix: Use the Uconnect touchscreen center console display as an alternative interface by navigating to Apps, Settings, My Car, and then selecting Engine Oil Life to complete the reset digitally.


Scenario C: Change Oil Warning Light Persists Despite 100% Display



  • Root Cause: A hard diagnostic trouble code (DTC) related to oil pressure sensor parameters or maintenance reminders triggered independently of the basic percentage monitor.
  • Actionable Fix: Scan the vehicle using an OBD-II diagnostic tool capable of reading manufacturer-specific powertrain codes, clear any pending service intervals, and perform a secondary hard reset of the instrument cluster.

Frequently Asked Questions



Can I reset the oil life monitor on a 2014 Jeep Grand Cherokee using the touchscreen?

Yes, vehicles equipped with the 8.4-inch Uconnect multimedia infotainment touchscreen can perform this function. Navigate to Apps, select Settings, tap the Vehicle category, choose System Information or My Car, and select the Oil Life reset utility.



How often should the oil life be reset on this vehicle?

You should only reset the oil life monitor immediately following a complete engine oil and filter change service. Resetting the monitor without changing the oil will cause the vehicle algorithm to miscalculate future wear intervals, potentially leading to engine mechanical damage.



Why does my 2014 Jeep Grand Cherokee require a specific oil viscosity?

Modern engines utilize variable valve timing and precise hydraulic oil pressure pathways that depend on exact fluid viscosities to operate hydraulic actuators efficiently. Using incorrect oil weights can trigger fault codes, degrade fuel economy, and cause premature internal wear.



What causes the Change Oil message to illuminate prematurely?

The Intelligent Oil Life Monitor calculates degradation based on engine operating hours, ambient temperature cycles, idle times, and trip distances. Excessive towing, extended idling in traffic, or harsh weather conditions accelerate the algorithm and trigger the warning light before standard mileage thresholds are reached.

Maintain Optimal Engine Health and Vehicle Longevity

Performing routine fluid maintenance and correctly updating your vehicle monitoring systems protects your investment and prevents unexpected mechanical breakdowns. Consult your certified mechanic or refer to factory service manuals for comprehensive mechanical inspections tailored to your specific powertrain configuration.


How to Reset Oil Life on Jeep Grand Cherokee 2015: Easy Guide ...

How to Reset Oil Life on Jeep Grand Cherokee 2015: Easy Guide ...

Read also: The schedule for the bus 172 bus route is explained here