How To Reset An A.O. Smith Water Heater: Technical Instructions For Electric And Gas Models

How To Reset An A.O. Smith Water Heater: Technical Instructions For Electric And Gas Models

Thermal Switch On Ao Smith Water Heater at Rachel Shortland blog

Resetting an A.O. Smith water heater requires identifying the specific safety trigger, such as the Energy Cut Off (ECO) switch on electric models or the gas control valve’s pilot ignition sequence on gas units. Most electric resets involve pressing the red high-limit button located behind the upper access panel once the water temperature has dropped below 120 degrees Fahrenheit.


Essential Safety Protocols and Tools for Water Heater Maintenance

Before attempting to interface with the internal components of an A.O. Smith water heater, it is critical to understand the mechanical and electrical safeguards in place. A "trip" of the reset button is rarely a random occurrence; it is typically a response to a high-limit condition where the water temperature has exceeded safe operational parameters, often reaching 170°F to 180°F. This safety mechanism, known as the Emergency Cut Off (ECO), prevents the tank from reaching temperatures that could lead to structural failure or severe scalding.

To perform a successful reset and diagnostic check, the following items and prerequisites are necessary:



  • Essential Tools: A Phillips-head screwdriver (for access panels), a flat-head screwdriver, a non-contact voltage tester, and a flashlight.
  • Safety Gear: Insulated work gloves and safety glasses to protect against potential electrical arcing or hot water spray.
  • Prerequisite Knowledge: Familiarity with your home's electrical panel (circuit breakers) and the location of the gas shut-off valve.
  • Duration: A standard reset procedure takes 15 to 30 minutes, though troubleshooting underlying causes may extend this timeframe.
  • Environmental Requirements: Ensure the area around the water heater is dry and clear of flammable materials or standing water before engaging with electrical components.

Procedural Workflow for Resetting Electric and Gas A.O. Smith Units

The reset process varies significantly between electric immersion-element models and gas-fired units. Following the correct sequence is vital to ensure the safety of the technician and the integrity of the appliance’s internal sensors.



Step 1: De-Energizing the System (Electric Models Only)

For electric A.O. Smith ProLine or Signature series heaters, the first priority is removing the power source. Locate the dedicated 240-volt double-pole circuit breaker in your electrical service panel labeled "Water Heater." Flip the switch to the OFF position. Use a non-contact voltage tester against the side of the heater's tank or at the entry point of the electrical conduit to confirm that no current is flowing to the unit. Attempting to reset a high-limit switch while the unit is energized carries a significant risk of electrical shock.



Step 2: Accessing the High-Limit ECO Switch

On the side of the tank, you will find two rectangular metal plates. The upper panel houses the primary thermostat and the high-limit reset button. Remove the screws securing this upper panel and set them aside. Carefully pull away the fiberglass insulation to reveal the plastic protective cover (also known as the "personnel protector"). Most A.O. Smith models use a snap-on protector; gently unclip it to expose the wiring and the thermostat assembly.



Step 3: Executing the Manual Reset

Locate the red button situated directly above the upper thermostat. This is the ECO switch.



  1. Observe the button's position. If it is protruding significantly, the switch has tripped.
  2. Press the red button firmly. You should hear or feel a distinct "click," indicating the internal bi-metal disc has re-engaged.
  3. If the button does not click or feels spongy, the water inside the tank may still be above the 120°F threshold required for the switch to reset. In this case, wait 30 minutes for the water to cool and try again.
  4. Once clicked, replace the plastic protector, tuck the insulation back into its original position, and reattach the metal access panel.


Step 4: System Re-Energization and Testing

Return to the circuit breaker panel and restore power. Listen for the faint "hum" or "hiss" of the upper heating element engaging. Wait approximately 30 to 60 minutes and check for hot water at the nearest faucet. If the water remains cold, or if the breaker trips immediately, there is likely a grounded heating element or a faulty thermostat requiring replacement.



Step 5: Resetting A.O. Smith Gas Water Heaters

Gas models do not have a "red button" reset in the same manner as electric models. Instead, "resetting" a gas unit usually involves clearing a lockout on the gas control valve or relighting the pilot.



  1. Electronic Ignition Models: If your unit has a Honeywell or White-Rodgers gas control valve with an LED status light, turn the control knob to the "OFF" position. Wait five full minutes for any residual gas to dissipate. Turn the knob back to "PILOT" or the desired temperature setting. If the unit has an intelligent control system, the LED will flash a code indicating the status.
  2. Pilot Relighting: For manual ignition units, turn the knob to "PILOT," press and hold the knob down, and repeatedly click the piezo igniter button until the status light begins to blink (usually a green or blue light). Continue holding the knob for 60 seconds to allow the thermopile to generate enough millivoltage to hold the gas valve open.
  3. Vapor Sensor Lockout: If the unit detects flammable vapors, it will lock out permanently. This requires a professional technician to clear the fault and ensure the environment is safe.

How To Connect Ao Smith Electric Water Heater at Stanley Urbina blog

How To Connect Ao Smith Electric Water Heater at Stanley Urbina blog

Technical Specifications and Operational Thresholds by Model Type

The following data provides the standard operational parameters and component specifications for the most common A.O. Smith residential water heaters. These metrics are essential for determining if a reset is a temporary fix or if the unit is operating outside of its engineered limits.



Component / Metric Electric ProLine Series Gas Atmos. Vent Series Vertex High Efficiency
Reset Trigger Temp 170°F - 180°F (77°C - 82°C) 185°F (ECO Integrated) Software Lockout / 190°F
Operating Voltage 240V AC (Standard) 750 mV (Thermopile) 120V AC (Blower/Control)
Resistance (Elements) 12.5 - 13.5 Ohms N/A N/A
Max Pressure Rating 150 PSI 150 PSI 150 PSI
Default Factory Set 120°F (49°C) 120°F (49°C) 120°F (49°C)
Reset Mechanism Manual Red Button (ECO) Power Cycle / Pilot Relight Digital Controller Reset

Diagnostic Failures and Component-Level Remedies

If the reset button frequently trips or the unit fails to produce hot water after a successful reset, the following scenarios represent the most common mechanical failures observed in A.O. Smith systems.



  • Scenario 1: Shorted Heating Element (Electric Models)



    • Root Cause: Over time, the outer sheath of the immersion heating element can crack due to sediment buildup or mineral calcification. This allows water to contact the internal filament, creating a "ground fault" or a "dry fire" condition that causes the ECO switch to trip instantly to prevent tank damage.
    • Actionable Fix: Turn off the power and use a multimeter to check for continuity between the element terminals and the tank itself. If continuity exists, the element is shorted and must be replaced using a 1-1/2 inch element wrench.
  • Scenario 2: Failed Thermostat Calibration



    • Root Cause: The upper or lower thermostat may "stick" in the ON position, failing to cut power when the set temperature is reached. This leads to runaway heating, eventually triggering the high-limit safety reset.
    • Actionable Fix: Observe if the water at the tap is excessively hot (boiling or steaming). If so, replace both thermostats. It is industry standard to replace both simultaneously to ensure consistent thermal cycling.
  • Scenario 3: Pilot Light Will Not Stay Lit (Gas Models)



    • Root Cause: A dirty or oxidized thermopile/thermocouple is the primary culprit. These sensors must generate a specific millivoltage (typically 350mV to 750mV) to keep the gas valve open. If the sensor is covered in carbon or has shifted away from the flame, it will shut down the gas flow.
    • Actionable Fix: Use a soft wire brush or fine-grit sandpaper to gently clean the tip of the thermopile. Ensure it is fully engulfed by the pilot flame. If the LED light flashes a "low millivoltage" code, replace the pilot assembly.
  • Scenario 4: Excessive Sediment Buildup



    • Root Cause: High mineral content in the water settles at the bottom of the tank. In electric models, this buries the lower element, causing it to overheat. In gas models, it creates an insulating layer that leads to "tank knocking" and localized overheating of the base, which can trip thermal sensors.
    • Actionable Fix: Perform a full tank flush. Attach a garden hose to the drain valve at the bottom of the unit, open the pressure relief valve, and allow the water to run until it is clear of white or brown flakes.

Frequently Asked Questions



Why does my A.O. Smith water heater reset button keep tripping?

The most common reason for a recurring trip is a grounded heating element or a faulty thermostat that is not regulating the temperature correctly. When the water exceeds approximately 170 degrees Fahrenheit, the ECO switch trips to prevent the water from boiling and creating dangerous pressure levels.



How do I know if my heating element is burnt out?

You can test the element using a multimeter set to the Ohms (Ω) setting. A functioning 4,500-watt element should register between 12 and 13 Ohms; a reading of zero (continuity) or infinity (open circuit) indicates the element has failed and is the likely reason the reset button was triggered.



Can I reset the water heater without turning off the power?

While technically possible to press the button, it is extremely dangerous and strictly advised against by A.O. Smith. The high-limit switch is located near high-voltage terminals (240V), and any slip of the hand or tool could result in a lethal electric shock or a short circuit.



What do the flashing lights on my A.O. Smith gas valve mean?

The LED indicator provides a diagnostic heartbeat. A single flash every three seconds usually indicates normal operation, while specific sequences (like two or four flashes) indicate issues such as a pressure switch failure, a blocked vent, or a detected flammable vapor lockout. Consult the chart on the side of your tank for model-specific codes.



Is it safe to bypass the high-limit reset button?

No, the high-limit switch is a critical safety device required by UL standards. Bypassing this switch can result in the water heater exploding due to excessive pressure or causing severe, life-altering burns. If the switch continues to trip, the underlying hardware failure must be addressed.

Professional Maintenance and Support

If your A.O. Smith water heater continues to malfunction after following these reset procedures, it may indicate a systemic failure of the internal lining or complex electrical components. Contact a licensed plumbing professional to perform a comprehensive diagnostic and ensure your home's hot water system remains compliant with local building codes.


Water Heater Top Element Not Working: Quick Fixes | Smart Water Source

Water Heater Top Element Not Working: Quick Fixes | Smart Water Source

Read also: Nj Hunting Zones Regulation Sets