How To Replace A Well Pump: A Comprehensive Technical Guide For Submersible Systems

How To Replace A Well Pump: A Comprehensive Technical Guide For Submersible Systems

How To Replace A Well Seal at Anthony Hackler blog

Replacing a submersible well pump requires a systematic approach to electrical safety, mechanical lifting, and hydraulic integrity, typically involving a significant investment of time for pull-and-reset operations. By ensuring the proper selection of pump horsepower, pipe material, and torque arrestors, homeowners can effectively restore water pressure and ensure system longevity without reliance on professional labor for every maintenance cycle.


Pre-Procedure Planning and Technical Requirements

Executing a well pump replacement necessitates a high degree of physical readiness and mechanical precision. Before breaking the seal on the well head, verify that the existing pump’s electrical specifications (voltage, phase, and horsepower) match the replacement unit. Standard submersible pumps operate on either 115V or 230V; mismatched electrical configurations will result in immediate motor failure or a tripping breaker.



  • Essential Gear and Tools:

  • Heavy-duty well seal or pitless adapter tool (the specialized T-handle for lifting).

  • Electrical multimeter for verifying voltage and checking continuity.

  • Pipe wrenches (minimum two 18-inch or 24-inch wrenches for high-torque connections).

  • Torque arrestors to prevent motor startup kickback.

  • High-quality electrical heat-shrink splice kit (do not use standard electrical tape).

  • Safety gear: Insulated waterproof gloves, steel-toed boots, and eye protection.

  • Assistance: A minimum of one additional adult is mandatory for safe extraction, as the weight of the column pipe and water column can exceed 300 pounds.

  • Benchmarks and Standards:

  • Estimated Duration: 4 to 8 hours depending on well depth and pump type.

  • Budgetary Scope: $400 to $1,500 for materials including the pump, control box, and wire/pipe components.

  • Regulatory Compliance: Check local codes regarding wellhead access; many jurisdictions require the use of a certified pitless adapter to prevent groundwater contamination.

Execution: The Step-by-Step Submersible Extraction and Installation



Step 1: Electrical De-energization and Site Preparation

Before physical contact, locate the primary well circuit breaker in the main service panel and flip it to the off position. Utilize a non-contact voltage tester or a multimeter to confirm the absence of current at the well control box. Once confirmed, remove the well cap or access the pitless adapter. If the system utilizes a pitless adapter, you must hook the pull-rod tool into the lifting eye of the adapter and use a downward motion to disengage the seal from the discharge pipe.



Step 2: Extraction of the Pump and Piping

As the pipe is lifted, it is critical to secure the assembly before every subsequent movement. As you pull each section of riser pipe—whether it is PVC or flexible polyethylene—you must utilize a support pipe or a "well-dog" (a U-shaped bracket) to hold the pipe at the casing rim.

Warning: Never rely on a single person to hold the weight of the pump. If the pump slips back into the well, it can cause catastrophic damage to the casing or shear the power cable.



Step 3: Mechanical Disconnection and Electrical Splicing

Once the pump reaches the surface, disconnect the electrical leads. Carefully remove the heat-shrink coating from the previous splice to reveal the wire connections. When installing the new pump, utilize a submersible splice kit. Each wire must be crimped with a heavy-duty butt connector and sealed with adhesive-lined heat shrink tubing to ensure the connection is completely waterproof.

Pro-Tip: Perform a continuity test on the motor leads before lowering the pump into the well. Verify that the resistance values match the manufacturer’s documentation to ensure the new motor is not defective out of the box.



Step 4: Re-installation and Testing

Attach a safety rope to the pump housing to serve as a backup to the riser pipe. Slowly lower the assembly back into the well, ensuring the power cable is secured to the riser pipe every 10 feet using stainless steel zip ties or electrical tape to prevent the cable from snagging on the well casing. Once the pitless adapter is reseated, reconnect the electrical power and monitor the control box for the hum of the motor and the subsequent pressure rise at the pressure tank.


Well Pumps & Booster Pumps - Rosco Corporation

Well Pumps & Booster Pumps - Rosco Corporation

Technical Specifications and Material Properties

The following table outlines the correlation between well depth and material requirements to ensure system pressure requirements are met without mechanical failure.



Component Type Material Recommendation Pressure/Duty Rating Application Context
Riser Pipe Schedule 80 PVC 250+ PSI Deep wells (above 200 feet)
Electrical Wire UF-B Copper Cable 12-10 AWG Submersible duty
Torque Arrestor Rubber/Neoprene High Impact Prevents casing abrasion
Safety Rope Polypropylene 500lb test min Emergency extraction
Control Box Capacitor-Start Matched to HP Required for 3-wire pumps

Common Site Failures and Field Fixes



  • Pump Fails to Start:

    • Root Cause: Tripped thermal overload or faulty control box relay.
    • Actionable Fix: Check the start capacitor in the control box with a multimeter; if the reading is infinite or zero, replace the capacitor.
  • System Short Cycles:

    • Root Cause: Waterlogged pressure tank or a faulty pressure switch.
    • Actionable Fix: Test the air charge in the tank (typically 2 PSI below the cut-in pressure). If the tank bladder is ruptured, replace the pressure tank.
  • Low Water Pressure or Flow:

    • Root Cause: The pump is running but the riser pipe has a hairline leak or a compromised check valve.
    • Actionable Fix: Inspect the check valve near the pump and at the surface. Replace with a stainless steel ball-type check valve to prevent backflow.

Frequently Asked Questions



How do I know what size pump to buy?

You must select a pump based on the GPM (gallons per minute) requirements of your household and the total dynamic head (the depth of the water level plus the height to your house and pressure requirements). Consult your original pump’s data plate to determine the current GPM and horsepower ratings, as these are tuned to your specific well’s recharge rate.



Can I replace a 3-wire pump with a 2-wire pump?

Yes, you can upgrade to a 2-wire pump, which eliminates the need for an external control box. However, this requires replacing the entire cable assembly and wiring configuration back to the pressure switch, as 2-wire pumps contain the starting components within the motor housing itself.



What is the purpose of the safety rope?

The safety rope provides a fail-safe method to retrieve the pump should the riser pipe joints fail or the pipe threads strip during a future pull. Always secure the rope to the wellhead casing or a secure external point, ensuring it remains taut enough to act as a secondary support without being the primary load-bearing element.



How often should a well pump be replaced?

A properly installed submersible pump has an expected service life of 10 to 15 years, depending on water chemistry and run cycles. Excessive sediment or iron content in the water can reduce this lifespan by causing premature wear on the pump’s impellers.

Professional Maintenance and System Longevity

Regular monitoring of your pressure tank’s air charge and your well’s draw-down levels will significantly extend the life of your new pump. If you encounter persistent electrical issues or suspect your well casing is compromised, contact a licensed groundwater professional to perform a down-well camera inspection to prevent more costly repairs.


Cost To Replace Well Pump And Pressure Tank | Gas Furnace

Cost To Replace Well Pump And Pressure Tank | Gas Furnace

Read also: Arizona White Pages: Residential and Business Search Directory