How To Remove Cycling Pedals: The Authoritative Guide To Professional Extraction And Maintenance

How To Remove Cycling Pedals: The Authoritative Guide To Professional Extraction And Maintenance

How To Remove Bike Pedals: A Step-by-Step Guide - BikeMag

Successful bicycle pedal removal requires mastering the distinct directional threading of the drive and non-drive sides: the right-side pedal uses a standard right-hand thread, while the left-side pedal features a reverse or left-hand thread. By utilizing a high-leverage 15mm pedal wrench or an 8mm hex key and following the "back to off" rule—turning the tool toward the rear of the bike—mechanics can safely extract pedals without damaging crank arm threads.


Professional Equipment Selection and Pre-Maintenance Planning

Before attempting to remove pedals, it is imperative to identify the specific interface of your componentry and gather the appropriate mechanical leverage tools. Pedals are exposed to high torque, road salt, moisture, and grit, which often leads to galvanic corrosion between the steel pedal spindle and the aluminum crank arm. Selecting the correct tool is the difference between a five-minute job and a stripped crank arm requiring a costly replacement.

Most modern cycling pedals utilize one of two interfaces: a 15mm wrench flat located on the spindle between the pedal body and the crank arm, or an internal hex socket (usually 6mm or 8mm) located at the end of the spindle, accessible from the back of the crank arm. Higher-end clipless pedals from brands like Shimano, Look, or Time almost exclusively use the internal hex interface to save weight and improve aesthetics.



Essential Tooling and Preparation Checklist



  • Pedal Wrench (15mm): A dedicated cycling pedal wrench is significantly thinner than a standard shop wrench, allowing it to fit into the narrow gap between the pedal and the crank arm. It also features a longer handle (typically 12 to 14 inches) to provide the necessary mechanical advantage.
  • Hex/Allen Keys: A high-quality 6mm or 8mm hex key is required for pedals without wrench flats. For seized pedals, a long-handled hex bit socket attached to a 3/8-inch drive breaker bar is preferred over a standard L-shaped Allen key.
  • Penetrating Lubricant: A high-performance solvent such as PB Blaster or Liquid Wrench is essential for pedals that have been installed for more than a year without service.
  • Work Stand or Stable Surface: While not strictly mandatory, a repair stand keeps the bike at chest height and prevents the drivetrain from moving during high-torque applications.
  • Cleaning Supplies: Isopropyl alcohol (90%+) and a clean lint-free rag for cleaning the crank arm threads post-removal.
  • Estimated Duration: 10–20 minutes for standard maintenance; 45+ minutes for seized components.
  • Technical Standard: Most modern adult bicycles use a 9/16" x 20 TPI (threads per inch) standard. Older or inexpensive "one-piece" cranks may use a 1/2" x 20 TPI standard.

Systematic Procedure for Pedal Extraction and Thread Preservation

The most common error in pedal removal is attempting to turn the spindle in the wrong direction, which effectively tightens the pedal and can strip the relatively soft aluminum threads of the crank arm. Following this specific sequence ensures safety for both the mechanic and the equipment.



Step 1: Positioning the Bicycle and Drivetrain

Before applying force, position the bicycle so it is stable. If you are not using a repair stand, lean the bike against a wall with the side you are working on facing outward. Shift the chain into the largest (outer) chainring. This serves as a safety measure: if the wrench slips while you are applying downward pressure, the teeth of the chainring will be covered by the chain, preventing "chainring bite" or lacerations to your hands and knuckles.

Rotate the crank arm so it points toward the front of the bike (the 3 o'clock position for the right side, or the 9 o'clock position for the left side). This orientation allows you to use your body weight to push the wrench downward, which is safer and more effective than pulling upward.



Step 2: The Right-Side (Drive-Side) Extraction

The right pedal (the side with the chain and gears) utilizes a standard right-hand thread. To loosen this pedal, you must turn the spindle counter-clockwise.



  1. Attach your 15mm pedal wrench to the spindle flats so the handle points toward the front of the bike at a slight upward angle.
  2. If using a hex key from the back of the crank arm, remember that the direction of rotation is mirrored. From the perspective of looking at the back of the crank, you will turn the hex key clockwise to loosen the pedal (which results in a counter-clockwise movement of the spindle itself).
  3. Apply firm, steady downward pressure on the wrench handle, pushing toward the rear of the bike.
  4. Once the initial "crack" of the seal is broken, continue unthreading by hand.

Pro-Tip: If the pedal is stubborn, align the wrench handle so it is nearly parallel to the crank arm. Squeeze the wrench and the crank arm together with both hands to "pinch" the pedal loose, using the crank arm as a lever.



Step 3: The Left-Side (Non-Drive-Side) Extraction

The left pedal uses a left-hand (reverse) thread. This engineering choice prevents the rotation of the bearings from unscrewing the pedal while riding (a phenomenon known as precession). To loosen the left pedal, you must turn the spindle clockwise.



  1. Rotate the left crank arm so it points toward the front of the bike (9 o'clock).
  2. Attach the 15mm wrench or insert the hex key.
  3. Push the wrench handle toward the rear of the bike (clockwise rotation).
  4. Maintain a perpendicular angle between the tool and the spindle to prevent the tool from slipping and rounding the flats or the hex socket.

Warning: Never use an impact driver on carbon fiber crank arms. The high-frequency vibration and sudden torque peaks can cause delamination or crack the internal threaded aluminum insert.



Step 4: Cleaning and Thread Inspection

Once the pedals are removed, the job is not complete until the interface is prepped for reinstallation or storage. Use a degreaser and a small wire brush or a stiff toothbrush to scrub the internal threads of the crank arms. Look for signs of "cross-threading"—flattened or shiny bits of aluminum that indicate the threads were damaged during a previous installation.

Inspect the pedal spindles for any signs of pitting or rust. If you intend to reinstall the pedals, wipe the threads dry and apply a fresh, liberal coating of marine-grade grease or an anti-seize compound. This prevents the chemical bonding (cold welding) that makes future removal difficult.


How to Easily Remove Bike Pedals : 4 Steps - Instructables

How to Easily Remove Bike Pedals : 4 Steps - Instructables

Pedal Interface Standards and Torque Specifications

Understanding the technical dimensions of pedal spindles is vital when switching between different types of bicycles (e.g., road, mountain, or vintage). The following table outlines the industry standards for thread pitch, tool requirements, and the necessary torque for secure installation.



Specification 3-Piece Crank (Standard) 1-Piece Crank (BMX/Kids) High-Performance Clipless
Thread Diameter 9/16 inch 1/2 inch 9/16 inch
Threads Per Inch 20 TPI 20 TPI 20 TPI
Primary Tool 15mm Pedal Wrench 15mm Pedal Wrench 8mm Hex (Internal)
Right Pedal Direction Counter-Clockwise (to loosen) Counter-Clockwise (to loosen) Counter-Clockwise (to loosen)
Left Pedal Direction Clockwise (to loosen) Clockwise (to loosen) Clockwise (to loosen)
Recommended Torque 35–40 Nm 30–35 Nm 35–55 Nm
Common Materials Chromoly Steel / Aluminum Carbon Steel Titanium / Chromoly Steel

Solutions for Seized Threads and Rounded Bolt Heads

In many cases, neglect or environmental exposure causes pedals to become "frozen" in the crank arm. If the standard procedure fails, professional mechanics employ the following escalation tactics to break the bond without destroying the components.



  • Scenario: The Pedal Spindle is Seized and Won't Budge



    • Root Cause: Galvanic corrosion or lack of grease at the time of installation has caused the steel spindle and aluminum crank threads to fuse at a molecular level.
    • Actionable Fix: Apply a dedicated penetrating oil (not a standard lubricant) and allow it to soak for at least 6 to 12 hours. If it remains stuck, use a "cheater bar"—a hollow metal pipe slipped over the handle of your wrench—to increase the radius of leverage. Ensure the bike is held firmly by an assistant to prevent the repair stand from tipping.
  • Scenario: The Internal Hex Socket is Rounded Out



    • Root Cause: Using a worn Allen key or a key that was not fully seated in the socket before applying high torque.
    • Actionable Fix: Use a hammer to tap a slightly oversized Torx bit (e.g., a T-45 or T-50) into the rounded hex hole. The "teeth" of the Torx bit will bite into the metal, allowing you to turn the spindle. Alternatively, if there is enough room, use a set of locking pliers (Vise-Grips) on the outside of the spindle shoulder, though this will likely mar the surface.
  • Scenario: The Crank Arm Spins, Making it Impossible to Apply Force



    • Root Cause: Lack of a work stand or improper body positioning.
    • Actionable Fix: Rotate the crank arm so it is adjacent to the chainstay or down tube. Use a toe strap or a heavy-duty zip tie to "lock" the crank arm to the frame. This creates a solid base against which you can pull the wrench, concentrating all your energy on the thread rotation rather than holding the bike steady.
  • Scenario: Thermal Expansion Resistance



    • Root Cause: Extreme thread interference.
    • Actionable Fix: Using a heat gun (not a torch, which can ruin the temper of the metal or bubble the paint), carefully heat the crank arm around the pedal spindle. Aluminum expands at a faster rate than steel. By heating the crank, the threaded hole expands slightly more than the steel spindle, often breaking the corrosive bond and allowing for removal.

Frequently Asked Questions



Why is the left pedal reverse-threaded?

The left pedal uses a left-hand thread to prevent a phenomenon called precession. As you pedal, the force exerted on the bearings would naturally tend to unscrew a right-hand threaded spindle on the left side. Reverse threading ensures that the mechanical action of riding actually helps keep the pedal tightened against the crank arm.



What should I do if I can't remember which way to turn the wrench?

The most reliable mnemonic is "back to off." Regardless of which side of the bike you are on, if you place your wrench on the pedal spindle with the handle pointing upward, turning the wrench toward the back of the bike will always loosen the pedal. Conversely, turning toward the front wheel will always tighten it.



Can I use a standard 15mm wrench from a hardware store?

Generally, no. Standard 15mm wrenches are usually too thick to fit between the pedal body and the crank arm. A specialized pedal wrench is ground thinner (usually around 3mm to 5mm thick) to accommodate this narrow clearance. Additionally, standard wrenches are often too short to provide the 35+ Nm of torque required to break a pedal loose.



Do I need to grease the threads before putting pedals back on?

Yes, greasing the threads is arguably the most important step in pedal maintenance. A thick waterproof grease or an anti-seize compound creates a barrier that prevents water and salt from entering the threads, which stops the corrosion that leads to seized pedals. It also allows for more accurate torque application during installation.



Is it possible to remove pedals with just a multi-tool?

While some multi-tools include a 6mm or 8mm hex key, they rarely offer enough leverage to remove a properly torqued pedal. Attempting to use a small multi-tool often results in hand injuries or rounded-out bolt heads because the tool is difficult to keep square in the socket while applying maximum force.

Optimize Your Cycling Performance and Maintenance

Mastering the nuances of pedal removal is a foundational skill for any cyclist looking to perform their own maintenance or prepare their bike for travel. For more advanced drivetrain tutorials and professional-grade workshop tips, continue exploring our technical maintenance series to keep your ride running at peak efficiency.


How to Install Clipless Pedals | Guide to Clipless Bike Pedals

How to Install Clipless Pedals | Guide to Clipless Bike Pedals

Read also: Former good morning america hosts are exposing industry secrets now