How To Put Skateboard Trucks On: The Professional Mounting Guide

How To Put Skateboard Trucks On: The Professional Mounting Guide

Defiant Board Society Adjustable Skateboard Trucks - Tune Your Ride for ...

Installing skateboard trucks requires precise alignment of the kingpins facing inward toward the center of the board to ensure proper steering geometry. The process involves threading high-tensile 10-32 UNF hardware through the deck's pre-drilled mounting holes and securing them with nylon-insert locknuts tightened to a flush finish. Achieving a professional-grade setup prevents deck delamination, eliminates hardware rattle, and ensures mechanical consistency during high-impact maneuvers.


Pre-Mounting Inspection and Component Synchronization

Before initiating the mechanical assembly, it is imperative to verify the compatibility of your components. Standard modern skateboard decks utilize a universal four-hole mounting pattern, but the specific hardware length you choose is dictated by whether or not you are utilizing riser pads. A standard "street" or "trick" setup usually omits risers to maintain a lower center of gravity, necessitating 7/8 inch or 1-inch bolts. If you are adding 1/8 inch or 1/4 inch vibration-dampening risers, you must scale your hardware length accordingly to 1.125 inches or 1.25 inches to ensure the nylon locking ring of the nut fully engages with the bolt threads.



Required Tooling and Hardware Checklist



  • Skateboard Trucks: One pair (two units), typically consisting of the baseplate, hanger, bushings, and kingpin assembly.
  • Hardware Set: Eight high-tensile steel bolts (Phillips or Allen head) and eight matching 3/8-inch nylon-insert locknuts.
  • The "Skate Tool" or Equivalent: A 3/8-inch socket for the mounting nuts, a 1/2-inch socket for the axle nuts, and a 9/16-inch socket for the kingpin.
  • Driver: A #2 Phillips head screwdriver or a 1/8-inch Allen key, depending on your hardware type.
  • Grip Tape Awl: Any thin, pointed metal object (a screwdriver or a spare bolt works) to puncture the grip tape from the underside.
  • Optional Riser Pads: Required for larger wheel clearances (typically 56mm+) or vibration reduction on rough terrain.


Technical Benchmarks



  • Estimated Duration: 15–20 minutes for a complete, calibrated installation.
  • Budget: Hardware sets typically range from $2.00 to $6.00 USD.
  • Standard Torque: Hardware should be tightened until the bolt head is flush with or slightly recessed into the grip tape, without crushing the wood fibers of the deck.

The Precision Installation Sequence for Skateboard Trucks

Properly mounting trucks is a foundational skill that affects the structural integrity of your maple deck. Follow this systematic workflow to ensure your equipment performs at professional standards.



Step 1: Puncturing the Grip Tape

If you are working with a freshly gripped deck, the mounting holes will be covered by the silicon carbide grit. Flip the board over so the graphic side faces up. Use a screwdriver or a spare mounting bolt to push upward through the eight pre-drilled holes in the wood. This creates a small "pimple" or protrusion in the grip tape on the top side of the board. Flip the board back over and use your driver to push through these protrusions from the top down. This clears the grit and ensures the bolt heads will seat cleanly without snagging the tape.

Pro-Tip: For a cleaner look, use a file or the side of a screwdriver to rub the edges of the holes on the grip tape side before inserting bolts. This prevents the tape from cracking or peeling around the hardware over time.



Step 2: Orientation and Kingpin Alignment

This is the most critical stage of the installation. A common beginner error is mounting trucks backwards. For a standard skateboard, the kingpins (the large central bolts holding the truck together) must face inward toward each other. When looking at the bottom of the board, the bushings of the front truck should face the bushings of the rear truck.

Warning: Mounting trucks with kingpins facing outward (toward the nose and tail) will cause the board to steer in the opposite direction of your lean, making it virtually unrideable and potentially dangerous.



Step 3: Hardware Insertion and Riser Placement

Place the deck on its side or upside down. Insert the four bolts through the top of the deck (the side with the grip tape). If you are using riser pads, slide the pad onto the bolts from the underside of the deck now. Ensure the holes in the riser pad align perfectly with the bolts. The "logo" side of the riser (if applicable) usually faces the ground, though orientation for flat risers is purely aesthetic.



Step 4: Seating the Baseplate

Align the truck's baseplate holes with the four bolts protruding from the bottom of the deck. Slide the baseplate onto the bolts. While holding the truck in place with one hand, use your other hand to thread the 3/8-inch nylon-insert locknuts onto the ends of the bolts. Turn them clockwise until they are finger-tight. This will keep the assembly in place while you prepare for the final torque application.



Step 5: The Cross-Pattern Tightening Technique

To prevent the baseplate from seating unevenly or causing "pressure cracks" in the deck plies, you must tighten the hardware using a diagonal or "X" pattern—much like tightening the lug nuts on a car tire.



  1. Place your screwdriver or Allen key into the bolt head on the top of the deck.
  2. Fit the 3/8-inch socket of your skate tool onto the nut on the underside.
  3. Hold the bolt stationary with the driver and rotate the nut with the socket tool.
  4. Tighten the first bolt 50% of the way, then move to the bolt diagonally opposite to it. Repeat for the remaining two bolts.


Step 6: Final Calibration and Flush Seating

Continue the diagonal tightening until the heads of the bolts are pulled flush with the top of the grip tape. You should not be able to feel the bolt heads protruding if you run your hand over them. On a new deck, you may hear a slight "creaking" or "popping" sound; this is the bolt head compressing the top layer of maple to create a countersunk fit.

Pro-Tip: Do not over-tighten. If the bolt head sinks more than 1-2 millimeters into the wood, you are crushing the structural plies, which can lead to premature deck snapping at the truck line.


Simple Ways to Put Trucks on a Skateboard: 15 Steps

Simple Ways to Put Trucks on a Skateboard: 15 Steps

Standardized Hardware Sizing and Torque Benchmarks

Selecting the correct hardware length is vital for both safety and aesthetics. The following table provides the industry-standard pairings for various setup configurations.



Configuration Type Riser Thickness Recommended Bolt Length Socket Size Requirement
Standard Street / Park No Riser 7/8" to 1" 3/8" (Nuts) / #2 Phillips
Loose/Vibration Dampening 1/8" Riser 1.125" (1 1/8") 3/8" (Nuts) / #2 Phillips
Cruiser / Large Wheels 1/4" Riser 1.25" (1 1/4") 3/8" (Nuts) / #2 Phillips
Longboard / High Clearance 1/2" Riser 1.5" to 1.75" 3/8" (Nuts) / #2 Phillips
Drop-Through Mounting N/A 1" to 1.25" 3/8" (Nuts) / #2 Phillips

Common Mounting Errors and Mechanical Solutions

Even experienced skaters can encounter issues during the mounting process. Identifying the root cause of hardware failure is essential for maintaining a safe ride.



  • Scenario: Hardware Continues to Loosen During Use



    • Root Cause: The nylon ring inside the locknut has been stripped or heat-damaged from excessive re-use, or the hardware length is too short to reach the nylon locking mechanism.
    • Actionable Fix: Replace the nuts with fresh 10-32 nylon-insert locknuts. Ensure at least two full threads of the bolt are visible beyond the nut once tightened to ensure the nylon ring is fully engaged.
  • Scenario: The "Clicking" Sound During Turns



    • Root Cause: The hardware is slightly loose, allowing the metal baseplate to shift against the wooden deck or the plastic riser pad.
    • Actionable Fix: Re-tighten all eight bolts using the cross-pattern technique. If the noise persists, check the pivot cup of the truck for wear and apply a small amount of paraffin wax or soap shavings to the pivot point.
  • Scenario: Bolt Heads Won't Sit Flush with the Grip Tape



    • Root Cause: The grip tape was not properly cleared from the hole, or the hardware has a "Pan Head" rather than a "Countersunk Head" design.
    • Actionable Fix: Ensure you are using "Countersunk" skateboard-specific hardware. If the tape is the issue, remove the bolt and use a sharp blade to trim a tiny circle of grip tape away from the diameter of the hole before re-inserting.
  • Scenario: Pressure Cracks Appearing Near Hardware



    • Root Cause: Over-tightening the hardware or riding without risers on high-impact landings, causing the baseplate's rigid edges to stress the wood.
    • Actionable Fix: Loosen the hardware slightly so it is flush rather than deeply recessed. Consider adding a thin 1/16" shock pad (soft riser) to distribute the energy of landings more evenly across the deck surface.

Frequently Asked Questions



Which way do the trucks face on a skateboard?

The kingpins, which are the large bolts containing the rubber bushings, must face inward toward the center of the board. This ensures that when you lean to the left, the mechanical geometry of the trucks pivots the axles to steer the board to the left.



Do I need to use riser pads when putting on trucks?

Riser pads are optional and primarily used to prevent "wheel bite," which occurs when the wheels touch the deck during a sharp turn. If you are using wheels larger than 55mm, or if you prefer very loose trucks, adding at least a 1/8-inch riser pad is highly recommended for safety.



How tight should the mounting hardware be?

The mounting hardware should be tightened until the head of the bolt is perfectly flush with the grip tape. It should be snug enough that there is zero movement between the truck baseplate and the deck, but not so tight that it creates deep indentations or cracks in the wood.



What is the difference between Phillips and Allen hardware?

The difference is purely a matter of preference regarding the tool interface. Phillips heads are more common and easier to find tools for, while Allen (hex) heads are less likely to "strip" or round out over time if you frequently assemble and disassemble your board.



Why are some bolts in a hardware set a different color?

Many hardware brands include one or two bolts of a different color (e.g., seven black bolts and one gold bolt). This is a visual aid; skaters install the colored bolt at the "nose" (front) of the board so they can instantly tell which direction the board is facing while riding.

Finalize Your Professional Skateboard Build

Mastering the hardware installation process ensures your skateboard remains a precise extension of your movements rather than a liability. Secure your trucks today and experience the stability of a perfectly calibrated professional setup.


Skateboard Trucks How To Put On at Jorge Damon blog

Skateboard Trucks How To Put On at Jorge Damon blog

Read also: New research will clarify the mystery of how did president garfield died