How To Put Magnets In DND Minis: The Definitive Guide To Miniature Magnetization
Magnetizing your Dungeons & Dragons miniatures using neodymium rare-earth magnets eliminates transport damage, simplifies modular weapon swaps, and secures transport trays. Achieving a permanent, flush-mounted hold requires precise drill bit sizing, correct magnetic polarity pairing, and high-strength cyanoacrylate application to withstand frequent table usage.
Tooling Specifications and Material Requirements
Transporting custom-painted miniatures or managing modular character sheets with interchangeable gear requires a standardized hardware ecosystem. Neodymium magnets, specifically the N52 grade, provide the highest magnetic flux density commercially available, ensuring a small footprint can support heavy metal or resin components.
Essential Equipment and Materials:
- N52 Neodymium Disc Magnets: Common sizes include 1/8 inch by 1/16 inch for standard bases, and 1/16 inch by 1/32 inch for arms and weapon swaps.
- Pin Vise Hand Drill: Equipped with a matching precision twist drill bit (e.g., 1mm, 2mm, or 3mm corresponding to exact magnet diameters).
- Cyanoacrylate Glue (CA Glue): Medium viscosity, paired with an accelerator spray for instant curing.
- Marking Tools: A fine-tip permanent marker or sharpie to track magnetic polarity.
- Safety Equipment: Dust mask for resin/plastic particulates and safety glasses.
Prerequisite Knowledge and Operational Standards:
- Polarity consistency across an entire miniature collection prevents incompatible weapon configurations and unusable transport cases.
- Undersizing drill holes by fractions of a millimeter ensures a friction-fit that prevents the magnet from spinning inside wet glue.
- Estimated budget ranges from fifteen to thirty dollars for a starter kit of bits, glue, and a hundred-pack of assorted magnets, with a completion time of fifteen to thirty minutes per miniature.
Step-by-Step Miniature Magnetization Workflow
Step 1: Polarity Verification and Marking
Before touching any cutting or drilling tools, establish a strict polarity standard. Take a stack of N52 magnets and pull one off the top. Use a permanent marker to color the outward-facing side of every magnet you plan to install into your miniature bodies, movement trays, or handle grips.
Warning: Mixing up magnet orientation during installation will cause your miniature components to repel each other instead of attracting. Always double-check your polarity stack before applying adhesive.
Step 2: Drilling the Anchor Cavity
Select a twist drill bit that matches the outer diameter of your magnet. For a 3mm disc magnet, use a 3mm or slightly undersized metric bit. Place the tip of the pin vise on the bottom center of the miniature plastic or resin base. Apply steady, downward pressure while rotating the pin vise handle clockwise. Clear plastic shavings or resin dust from the hole frequently by blowing on the surface or using a soft brush. Periodically test-fit the magnet to check depth. The top surface of the magnet should sit flush with or slightly below the surrounding material to maintain a flat base profile.
Pro-Tip: If you are magnetizing a slotted slotta-base, fill the plastic slot with green stuff epoxy putty or milliput first, let it cure, and then drill your clean anchor hole into the solid putty matrix.
Step 3: Adhesive Application and Seating
Dispense a single drop of medium-viscosity cyanoacrylate glue onto a non-porous scrap surface, such as a piece of plastic or a ceramic tile. Dip the tip of an unused hobby knife, toothpick, or wire applicator into the glue and transfer a minuscule amount directly inside the drilled cavity. Too much glue will flood the hole, squeeze out over the top of the magnet, and foul the magnetic face or ruin your miniature's paint job. Use tweezers to pick up the magnet, ensuring the marked polarity side faces the correct direction, and press it firmly into the cavity until it bottoms out against the plastic.
Step 4: Curing and Component Locking
Hold the magnet in place for ten to fifteen seconds using a non-magnetic tool, such as the flat end of a hobby knife or a wooden toothpick. If you are using a chemical accelerator, apply a very light mist from a distance to instantly polymerize the cyanoacrylate. Allow the miniature to rest undisturbed for at least ten minutes before testing the magnetic connection against steel transport sheets or opposing weapon arms.
Dnd Map DM Screen For DND, Mini Dice Set DND With 4 Luazuri Dnd Magnets
Technical Parameter Comparison for Miniature Magnetization
| Component Target | Recommended Magnet Size | Drill Bit Size | Primary Application |
|---|---|---|---|
| Standard 25mm/28mm Base | 1/8" x 1/16" (3mm x 1.5mm) | 3mm Twist Bit | Securing minis to magnetic sheet transport trays |
| Large Monster 50mm+ Base | 1/4" x 1/16" (6mm x 1.5mm) | 6mm Forstner or Twist Bit | Heavy stability for oversized pewter or resin models |
| Infantry Arms and Weapons | 1/16" x 1/32" (1.5mm x 1mm) | 1.5mm Micro Bit | Modular weapon swaps and hand accessories |
| Monster Wings and Tails | 3/32" x 1/16" (2mm x 1.5mm) | 2mm Twist Bit | Disassembling large models for compact storage boxes |
Troubleshooting Common Magnetization Failures
The magnet spins inside the drilled hole after gluing:
- Root Cause: The drill bit was slightly too large, or the hole was bored out unevenly during the manual pin vise rotation.
- Actionable Fix: Pry the loose magnet out using the tip of a hobby knife, clean out the old adhesive, fill the oversized hole with a tiny ball of green stuff epoxy putty, and press a fresh magnet directly into the soft putty.
Magnetic components repel each other or twist sideways upon connection:
- Root Cause: Polarity was reversed during installation, or the magnet shifted on its axis while the cyanoacrylate was curing.
- Actionable Fix: If the glue has fully cured, use a pair of hobby pliers to twist and pull the magnet free. Clean the cavity, verify your master polarity stick, and reinstall the magnet with fresh adhesive and an accelerator spray.
The magnet pulls out of the base when lifting the miniature from the tray:
- Root Cause: The bond between the smooth nickel plating of the magnet and the cyanoacrylate failed, or there was a release agent residue inside the drilled hole.
- Actionable Fix: Scuff the flat back of the magnet lightly with fine-grit sandpaper to create a mechanical tooth for the glue, and wipe the cavity with isopropyl alcohol before re-gluing.
Frequently Asked Questions
What size magnets are best for standard D&D miniatures?
The industry standard for normal 25mm to 32mm base miniatures is a 1/8 inch diameter by 1/16 inch thickness disc magnet (approximately 3mm by 1.5mm). This size provides sufficient pulling force to hold a plastic or metal miniature securely to a steel transport sheet without adding excessive weight or punching through the bottom of the plastic base.
How do I ensure I never mix up magnet polarities?
Keep a master magnetic polarity wand on your workbench by gluing a magnet to the end of a popsicle stick and marking it clearly. Always touch your loose installation magnets to this master stick immediately before applying glue to confirm that every part of your project attracts rather than repels.
Can I magnetize hollow resin printed miniatures?
Yes, but you must ensure the resin shell is thick enough to drill into without breaking through to the hollow interior cavity. If the walls are too thin, fill the interior space beneath the mounting point with UV-cured resin or two-part epoxy putty to create a solid anchor block before drilling.
Do I need special tools to drill into miniature plastic?
A standard pin vise hand drill is all you require for working with polystyrene games workshop plastics, PVC board game figures, and cured tabletop resins. Avoid using high-speed electric power drills, as they generate excess friction heat that melts plastic miniatures and ruins delicate sculpt details.
Upgrade your tabletop organization and protect your painted collection today by outfitting your entire campaign roster with reliable, transport-ready magnetic bases.