How To Put Harley In Transport Mode: The Complete Step-by-Step Guide

How To Put Harley In Transport Mode: The Complete Step-by-Step Guide

2005 Harley Davidson Ultra Classic Motorcycle | Transportation | BigIron

Harley-Davidson transport mode disables the Smart Security System motion detector, preventing the alarm from triggering while the motorcycle is being hauled on a trailer, loaded into a truck bed, or rolled on a ferry. Utilizing this feature ensures your battery is not drained by a false-triggering siren cycle while preserving your key fob's battery during transit.


Pre-Operation & Transport Preparation Checklist

Preparing a Harley-Davidson motorcycle for transit involves more than simply clicking the security system into transport mode. You must account for suspension compression, tie-down point integrity, and battery voltage stabilization to protect your investment over long distances.



  • Essential Gear, Tools, and Materials:

    • Soft-hook tie-down straps (minimum four ratchet straps with a rating of 1,200 pounds or higher).
    • Wheel chock designed specifically for motorcycle tire widths (ranging from standard 80mm front tires up to wide 130mm/140mm front touring wheels).
    • Handlebar straps or frame-mounted soft loops (avoid wrapping straps directly around chrome components, painted surfaces, or brake lines).
    • Working Harley-Davidson Smart Security FOB with a fresh CR2032 lithium coin cell battery.
  • Mandatory Prerequisite Knowledge and Standards:

    • Understand the difference between standard ignition off, accessory mode, and ignition on.
    • Familiarize yourself with your specific model's handlebar control layout, as switch housings vary between Touring, Softail, Sportster, and Dyna families.
    • Ensure the motorcycle is on level ground in neutral before beginning the electronic sequence.
  • Estimated Budget and Duration Benchmarks:

    • Time required: 3 to 5 minutes for electronic setup and proper strapping.
    • Cost: Zero dollars if utilizing existing hardware; $50 to $150 if purchasing dedicated motorcycle transport straps and a wheel chock.

Step-by-Step Transport Mode Activation Procedure



Step 1: Establish Ignition and Security Communication

Ensure you have the valid proximity key fob within two meters of the motorcycle. Turn the ignition switch (or the ignition/tombstone switch on the tank console, depending on your model) to the IGNITION position, or press the ignition button without engaging the starter if you ride a modern Touring or Softail model equipped with hands-free ignition. Verify that the console lights and instrument cluster activate fully, confirming the security system has recognized the fob's presence.

Warning: Never attempt to enter transport mode while the motorcycle is already in motion or while the security alarm is actively sounding, as the body control module (BCM) or security siren module (SSM) may ignore the command sequence.



Step 2: Execute the Disarm and Turn-Off Sequence

With the ignition currently powered on, press and hold both the left and right turn signal switches simultaneously for approximately two seconds. Alternatively, on certain models equipped with a handlebar security button or smart security integration, check your owner's manual for specific auxiliary switch prompts. Next, immediately turn the ignition switch to the OFF position while maintaining your physical presence near the motorcycle.



Step 3: Verify Transport Mode Activation via Turn Signals

Immediately after turning the ignition switch to the OFF position, both the left and right turn signal indicators on the instrument cluster will flash three times simultaneously. These triple flashes serve as the definitive confirmation signal from the security computer that transport mode is successfully engaged. The motion sensor is now sleeping, meaning bumps, vibrations, and tilting will not trigger the siren.

Pro-Tip: If the turn signals do not flash three times, the command was not registered by the security module. Simply turn the ignition back on, ensure the fob battery is strong, and repeat the simultaneous turn signal button hold before turning the ignition off again.



Step 4: Secure the Motorcycle to the Transport Vehicle

Once transport mode is confirmed active, load the motorcycle into your truck bed or onto your trailer using a secure ramp. Push the front wheel firmly into a locked wheel chock. Attach your soft-hook tie-down straps to sturdy structural points on the frame—such as the lower triple trees or the frame downtubes—and compress the front suspension evenly by roughly 25 to 30 percent of its total travel. Never compress the front or rear suspension to maximum travel, as sudden road impacts could blow fork seals or damage the valving.


Original 2 Harley / Indian / Cruiser Motorcycle Transport Kit - Bolt It On

Original 2 Harley / Indian / Cruiser Motorcycle Transport Kit - Bolt It On

Harley-Davidson Security Modes and Specifications Comparison



Security State Motion Detector Status Ignition State Power Draw Primary Use Case
Armed Mode Active (Triggers on tilt/vibration) Off Low (Quiescent BCM draw) Normal parking and overnight storage
Transport Mode Disabled (Ignores tilt/vibration) Off Low (Quiescent BCM draw) Trailering, towing, ferry transport
Disarmed Mode Inactive (Fob present) Accessory or Ignition Moderate to High Riding, maintenance, auxiliary audio

Common Transport Mode Failures and Field Fixes



  • Failure Scenario: Turn signals do not flash three times after turning the ignition off.

    • Root Cause: The key fob battery is weak, or the timing between pressing the turn signals and turning the ignition switch off was out of sync.
    • Actionable Fix: Replace the CR2032 battery inside the smart fob with a fresh lithium cell. Ensure you press both turn signal switches simultaneously before powering the ignition down.
  • Failure Scenario: The alarm starts blaring halfway through the journey despite following the activation steps.

    • Root Cause: Transport mode automatically cancels itself the moment an ignition cycle occurs while a valid key fob is detected nearby. If the key fob was left in the glovebox of a truck hauling the trailer and shifted close enough, the system woke up.
    • Actionable Fix: Keep the key fob at least 10 to 15 feet away from the motorcycle during transport, or place the fob inside a signal-blocking Faraday pouch.
  • Failure Scenario: Transport mode refuses to disengage once the bike arrives at its destination.

    • Root Cause: The system remains locked in transport mode or the security module has temporarily lost synchronization with the fob due to local radio frequency interference.
    • Actionable Fix: Turn the ignition switch to the IGNITION position with the valid fob present. If the bike fails to recognize the fob automatically, manually enter your 5-digit PIN using the left and right turn signal switches via the manual override procedure detailed in your owner's manual.

Frequently Asked Questions



How do I deactivate transport mode once I reach my destination?

Deactivating transport mode is automatic and straightforward. Simply bring the valid key fob within range of the motorcycle and turn the ignition switch to the IGNITION or ACCESSORY position. The security system will recognize the fob, drop transport mode, and restore normal motion-detector functionality.



Does transport mode drain the motorcycle battery?

No, transport mode does not consume extra electrical power. It merely commands the security system's microprocessor to ignore inputs from the internal accelerometer and tilt sensor, maintaining the exact same low quiescent current draw as standard armed mode.



What should I do if I lost my key fob and need to transport the bike?

If you do not have your smart security fob, you can bypass the security system entirely by turning the ignition on and using the left turn signal switch to cycle through digits and the right turn signal switch to advance, entering your pre-programmed 5-digit PIN manually. Once the security system is disarmed via PIN, you can load the motorcycle onto your trailer and drive without utilizing the electronic transport mode.



Can transport mode be used for everyday parking on windy days?

While you technically can use transport mode for parking, it is not recommended for unattended street parking because it leaves your bike vulnerable to theft without motion-alarm protection. Reserve transport mode exclusively for active transit scenarios where the bike is secured to a moving vehicle.

Safeguard your motorcycle during your next cross-country move or track day haul by mastering the transport mode sequence before loading up. Explore our library of technical guides for more expert Harley-Davidson maintenance tips and custom accessory installations.


Open Road Harley-Davidson® | Transport Mode | Open Road Harley-Davidson®

Open Road Harley-Davidson® | Transport Mode | Open Road Harley-Davidson®

Read also: Top 25 Grey Blending Ideas for Dark Hair Trending in 2024