The Professional Guide On How To Mount Antlers: A Step-by-Step DIY Manual

The Professional Guide On How To Mount Antlers: A Step-by-Step DIY Manual

How to mount elk sheds ~ Diy shed kits plans

Achieving a professional-grade antler mount requires precise skull plate preparation, structural reinforcement with high-grade epoxy, and the application of taxidermy-grade velvet or leather finishes. By adhering to standardized cleaning protocols and using rigid mounting hardware, you ensure long-term structural integrity and a trophy presentation that effectively showcases natural anatomy.


Essential Preparation and Required Taxidermy Supplies

Successful antler mounting depends on the initial state of the skull plate. Whether you are performing a European-style mount or a traditional plaque-based presentation, the foundational work is identical. Before starting, ensure you have a workspace with adequate ventilation and a heat-resistant surface.



  • Essential Gear and Tools:



    • Fine-tooth hacksaw or reciprocating saw with a metal-cutting blade for clean skull plate cuts.
    • Two-part structural epoxy putty or professional taxidermy skull adhesive.
    • Wood mounting plaque (oak, walnut, or pine) pre-drilled for wall hanging.
    • Industrial-grade mounting screws, wall anchors, and a heavy-duty hanger bracket.
    • Leather or velvet decorative trim to conceal the transition between bone and plaque.
    • Hydrogen peroxide (30% volume) for bone whitening.
    • Personal Protective Equipment (PPE): Nitrile gloves, safety goggles, and an N95 dust mask.
  • Technical Standards:



    • Duration: Expect 4 to 6 hours of active labor, excluding the chemical whitening process which requires 24 to 48 hours.
    • Budget: DIY kits typically range from 40 to 80 dollars, depending on wood quality and adhesive grade.
    • Prerequisite: The skull plate must be fully desiccated and free of organic tissue to prevent subsequent bacterial rot or lipid bleeding through the finished mount.

Execution Workflow for Secure Antler Mounting

The structural stability of your mount relies on how effectively the skull plate is anchored to the backer board. Follow these steps sequentially to ensure a professional finish.



Step 1: Skull Plate Trimming and Cleaning

Using your saw, make a clean, horizontal cut across the skull. The goal is to remove the brain cavity and excess bone to minimize weight and create a flat surface for mounting. Avoid cutting too close to the burr of the antler, as this weakens the structural attachment point. Once cut, submerge the plate in a mild degreaser or dish soap solution for 24 hours to remove residual oils.

Warning: Never use boiling water to clean a skull plate, as it causes the bone to become brittle and creates an oily residue that will stain the final mount over time. Always use a simmering water method at low temperatures if meat removal is still required.



Step 2: Whitening the Bone

After the skull plate is cleaned, apply a paste made of 30% hydrogen peroxide and magnesium carbonate. Coat all exposed bone surfaces generously. Wrap the plate in plastic wrap to keep the paste moist and prevent it from drying out prematurely. Let it sit in a room-temperature environment for 24 hours. After removing the paste, rinse thoroughly with cool water and allow it to air-dry completely in a shaded area.



Step 3: Structural Mounting to the Plaque

Center your prepared skull plate on the wood plaque. Mark the contact points and drill pilot holes into the skull plate from the underside of the plaque. Secure the skull plate to the plaque using heavy-duty wood screws.

Pro-Tip: If the skull plate is exceptionally porous or brittle, use a two-part structural epoxy between the bone and the wood. This creates a vibration-resistant bond that prevents the antlers from shifting or loosening over time.



Step 4: Applying Decorative Finishes

Once the skull plate is bolted to the plaque, you will notice a gap between the bone and the wood. This is the ideal time to apply leather, velvet, or a specialized skull cap cover. Apply a thin line of industrial-strength adhesive around the perimeter of the skull plate, then carefully stretch your chosen fabric over the bone, tucking the edges neatly into the gap between the wood and the bone.


How to Mount Antlers | Deer antler crafts, Deer antler decor, Antler crafts

How to Mount Antlers | Deer antler crafts, Deer antler decor, Antler crafts

Technical Specifications and Material Selection

The following table summarizes the requirements for selecting mounting materials based on the size of the antler and the desired aesthetic outcome.



Material Application Durability Aesthetic Impact
Structural Epoxy Skull-to-Plaque bonding Permanent High (Hidden)
Hardwood Plaque Base mounting surface Long-term Classic/Professional
Leather Wrap Covering skull transition Durable Traditional/Rustic
Velvet Trim Covering skull transition Moderate Formal/Elegant
Stainless Steel Screws Mechanical fixation High Essential for weight

Common Field Failures and Recovery Protocols

Even with careful planning, structural issues can arise during the curing phase. Address these problems immediately to prevent permanent damage to your trophy.



  • Root Cause: Grease seepage on the skull surface.

    • Actionable Fix: If you notice yellowish discoloration, the bone was not degreased sufficiently. Remove the mount from the wall, re-apply a degreasing agent, allow it to dry for 48 hours, and re-whiten with a fresh hydrogen peroxide paste.
  • Root Cause: Antlers shifting or wobbling on the plaque.

    • Actionable Fix: The pilot holes were likely drilled too wide for the screws. Extract the screws, fill the existing holes with a mixture of sawdust and epoxy, let cure for 24 hours, and re-drill smaller, more precise pilot holes.
  • Root Cause: Adhesive failure on the leather trim.

    • Actionable Fix: Use a cyanoacrylate-based adhesive (super glue) for quick repairs, or re-apply contact cement if the entire trim piece has detached. Ensure the surface is dust-free before re-bonding.

Frequently Asked Questions



Can I mount antlers that were found in the woods?

Yes, but they must be cleaned thoroughly. Ensure no soft tissue remains and that the bone is not excessively sun-bleached or crumbling, as brittle bone will not support a mechanical fastener.



Do I need to seal the bone after whitening?

It is highly recommended to apply a matte-finish acrylic sealer. This protects the bone from dust, humidity, and UV rays, preventing future yellowing or degradation of the skull plate.



How do I hide the gap between the skull plate and the plaque?

The most professional method is to use a skull cap cover, which is a pre-cut piece of synthetic or genuine leather designed to fit the contours of a deer skull, or by using a decorative trim of braided rope or leather piping.



Is it necessary to use a wood plaque?

While not strictly required, a wood plaque acts as a stabilizer, distributing the weight of the antlers across the wall surface. It also protects your wall from the sharp points of the skull plate and provides a clean, finished aesthetic.

Master Your Taxidermy Projects Today

Implementing these professional mounting techniques will elevate your antler display from a casual craft to a permanent, high-quality centerpiece. Order your premium mounting hardware and hardwood plaques now to begin your next trophy preservation project with confidence.


restlessrisa: How to Mount Antlers

restlessrisa: How to Mount Antlers

Read also: Drivers are frustrated with identogo staten island wait times