How To Measure For Ape Hangers: The Definitive Guide To Perfect Handlebar Fitment

How To Measure For Ape Hangers: The Definitive Guide To Perfect Handlebar Fitment

2006 Honda Shadow 750 Ape Hangers

Measuring for ape hangers requires calculating the vertical rise and pullback angle relative to your current riding posture to ensure ergonomic comfort and internal wiring compatibility. By establishing a neutral grip position and accounting for cable tension, you can determine the precise bar dimensions needed to avoid premature fatigue and control-line binding.


Pre-Procedure Planning and Required Measurement Tools

Before you commit to a specific set of ape hangers, you must establish a baseline for your motorcycle’s ergonomics. The transition to taller bars significantly alters your leverage over the front end and changes the required length for your throttle cables, clutch lines, and brake hoses. Estimating these needs correctly prevents the common mistake of purchasing bars that are either too tall for existing line slack or incompatible with your bike’s riser configuration.



  • Essential Tools: A heavy-duty measuring tape (preferably metal to maintain straightness), a length of garden hose or stiff wire (to simulate the bar shape), painter’s tape, a marker, and a notebook for recording measurements.
  • Mandatory Prerequisites: Ensure your motorcycle is in an upright position (using a motorcycle jack or center stand) rather than on the side stand to ensure an accurate vertical plane for measurement.
  • Estimated Duration: Plan for 60 to 90 minutes to ensure you simulate the grip position repeatedly, accounting for different torso angles.
  • Budgetary Considerations: Factor in not just the bars, but the hidden costs of extended braided stainless steel lines, wiring harness extensions (or soldering supplies), and potentially polyurethane riser bushings to handle the increased leverage of taller bars.

Precision Measurement Workflow for Custom Handlebars



Step 1: Establishing the Natural Reach Baseline

Sit on your motorcycle in your preferred riding position. Have an assistant hold your current handlebars or, if the bars are already removed, hold your arms up as if you were gripping the new bars. Your elbows should remain slightly bent at a natural, non-locked angle. This is your target grip center. Mark the location of your hands in the air relative to the center of your triple tree.



Step 2: Measuring Total Vertical Rise

Measure the distance from the top of your triple tree (or the base of your risers) to the center of your grip position. This is your true Rise. Most riders find that a rise ranging from 10 to 16 inches offers the best balance between aesthetics and blood flow.

Warning: Avoid excessive rise that places your hands above your shoulders, as this often leads to circulation issues in the hands and decreased steering precision during low-speed maneuvers.



Step 3: Determining Pullback and Width

Pullback refers to how far back the grips come toward the rider. To measure this, hold your hands in the desired grip position and have an assistant measure the horizontal distance from the center of the handlebar mounting point back to the plane of the hand grips. A standard pullback is usually between 6 and 10 inches. Ensure the width of the bars matches your shoulder breadth, as overly wide bars will strain your upper back and lats during long-distance rides.



Step 4: Accounting for Internal Wiring and Cable Routing

Measure the distance from the center of the mounting point to the tip of the bars for the width, but remember to subtract the width of your riser base. If you plan to run your wiring internally, add 2 inches to your estimated wiring harness extension needs to provide enough slack for full fork lock-to-lock movement.

Pro-Tip: Use a piece of old garden hose or thick gauge electrical wire bent into the shape you desire for your bars. This gives you a physical object to measure against, which is significantly more accurate than calculating the rise and pullback in empty space.


Meathook Ape Hangers - Dominator Industries

Meathook Ape Hangers - Dominator Industries

Handlebar Geometry and Ergonomic Parameters

When selecting your specific bar style, recognize that different manufacturers measure "rise" differently—some measure to the bottom of the grip, others to the center. Use the following reference table to reconcile these industry standards with your physical measurements.



Handlebar Characteristic Definition Impact on Ergonomics
Vertical Rise Height from base to top of grip Directly influences shoulder and neck fatigue levels
Pullback Distance grips move toward rider Determines the curvature of the spine and core engagement
Center Width Width between knurled mounting areas Must match riser-to-riser distance on triple tree
Grip Angle Pitch of the hand grip Affects wrist rotation and brake/clutch lever reach
End Rise Total verticality of the grips High end rise increases leverage but creates tighter turn radii

Common Fitment Failures and Field Corrections

Even with precise measuring, real-world variables often cause issues during the install. Addressing these immediately is critical for safety.



  • Cable Binding at Full Lock: This occurs when the throttle or clutch cable is too short.

    • Root Cause: Failure to measure at full fork lock (left and right) during the pre-installation phase.
    • Actionable Fix: Re-route the cables behind the triple tree or, if the binding persists, you must purchase longer braided stainless lines to prevent the throttle from sticking.
  • Handlebar Slip: The bars rotate forward or backward under heavy braking or acceleration.

    • Root Cause: Insufficient knurling at the mounting point or loose riser clamping bolts.
    • Actionable Fix: Clean the mounting surface with brake cleaner, apply a thin layer of grip paste or replace the stock rubber riser bushings with polyurethane or solid aluminum versions to eliminate leverage-induced flex.
  • Excessive Vibration: The taller the bar, the higher the amplitude of vibration at the grips.

    • Root Cause: Increased leverage magnifying the natural engine harmonics.
    • Actionable Fix: Install weighted bar-end dampers or vibration-dampening riser bushings to absorb the frequency before it reaches your hands.

Frequently Asked Questions



How do I know if I need new cables after installing ape hangers?

If you increase your handlebar height by more than 2 inches, your stock cables will likely reach their maximum tension point during full steering lock. Always test the slack by turning the bars to both steering stops; if the engine revs or the brake lever engages during this movement, you must order extended lines.



What is the legal height limit for ape hangers in my area?

Many jurisdictions measure handlebar height relative to the rider's shoulder position rather than a specific inch count. Check your local Department of Transportation or state vehicle codes to ensure your new bars do not exceed the legal limit for shoulder-height grip positioning.



Can I internally wire my own ape hangers?

Yes, you can internally wire your own bars if you have patience, a fish wire, and a basic understanding of molex connector removal. Use a stiff piece of mechanics wire or thin nylon string with a small weight to pull the harnesses through the tight bends of the bars, and ensure you use heat shrink tubing at exit points to prevent wire chafing.



Do I need to change my riser bolts when switching to tall apes?

Generally, you can reuse the stock mounting bolts, but you should inspect them for stretching or corrosion. If you upgrade to polyurethane or solid bushings, ensure the bolts are of the correct length to fully engage the threads in the triple tree without bottoming out prematurely.

Equip your motorcycle with the perfect set of ape hangers by following these precise measurement standards to ensure long-distance comfort and optimal mechanical safety. Order your custom control cables today to complete your upgrade and achieve the ideal riding geometry.


Ape Hanger Curve Brutale 1.1/2" Handlebars for Harley-Davidson Touring ...

Ape Hanger Curve Brutale 1.1/2" Handlebars for Harley-Davidson Touring ...

Read also: Type 1C Hair Guide: Essential Characteristics and Care Tips