How To Make A Paracord Turkey Tote: A Step-by-Step DIY Guide For Hunters

How To Make A Paracord Turkey Tote: A Step-by-Step DIY Guide For Hunters

Hunter Green & Black Paracord Turkey Tote Duck Goose Game Carrier/bag ...

A heavy-duty paracord turkey tote utilizes Type III 550 paracord to construct a dual-loop cinch system capable of carrying up to 45 pounds of wild game. By integrating a wide, hand-conforming Cobra weave handle with seamless metal rings, hunters can comfortably carry harvested birds over long distances without experiencing hand fatigue or cord slippage. This guide provides the precise measurements, knot-tying steps, and tensioning techniques required to build a lifetime-use game carrier.


Pre-Operation Planning & Equipment Checklist

Before assembling your DIY turkey tote (sometimes referred to as a game carrier or bird lanyard), you must choose materials that resist rot, mildew, and UV degradation. Wild turkeys are heavy, awkwardly shaped game birds; a mature gobbler can easily exceed 20 to 25 pounds. Carrying a bird of this size by its legs with bare hands or thin cordage will quickly cause bruising and deep skin cuts.

The double-loop cinch design described below uses a central braided handle to distribute weight across your palm, flanked by two adjustable sliding loops that tighten around the turkey’s legs or neck using gravity.



Required Materials and Benchmarks



  • Type III 550 Paracord: You will need approximately 30 to 35 feet of genuine nylon paracord. Avoid cheap polyester imitation cord, as it lacks elasticity, slips under load, and has a lower melting point, which makes heat-sealing knots difficult.
  • Welded Metal O-Rings: Two 1-inch or 1.25-inch welded stainless steel or solid brass O-rings. Ensure they are seamless and welded to prevent the paracord from slipping through gaps under load.
  • Heavy-Duty Shears: For clean cuts through the nylon sheath and seven inner core strands.
  • Butane Lighter or Torch: For melting and fusing the cut ends of the cord.
  • Masking Tape or Ruler: For marking out precise measurements.
  • Paracord Fid (Optional): A threaded blunt needle that helps thread paracord ends back through tight weaves.


Project Estimates



  • Estimated Cost: $8.00 to $15.00 USD (depending on the metal ring finish).
  • Time to Complete: 30 to 45 minutes.
  • Difficulty Rating: Intermediate (requires basic knowledge of the Cobra weave/Solomon bar and simple hitching knots).

Step-by-Step Turkey Tote Construction

Follow these structured steps to construct a professional-grade, double-loop paracord turkey carrier.



Step 1: Measure and Cut Your Cordage

To build a standard 8-inch braided handle with two 12-inch dropping cinch loops, you must cut two separate lengths of paracord.



  1. Cut the Core/Loop Strand: Measure and cut one piece of paracord to exactly 6 feet (72 inches). This strand will form the inner core of the handle and extend out of both ends to create the sliding cinch loops.
  2. Cut the Weaving/Wrap Strand: Measure and cut a second piece of paracord to exactly 16 feet (192 inches). This long strand will be used to wrap the core using the Cobra weave, creating a thick, comfortable, slip-resistant handle.
  3. Singe All Four Ends: Immediately use your lighter to melt the frayed ends of both cut cords. Pinch the melted nylon with a wet finger or press it against a cold metal surface to shape the melted plastic into a neat, hardened taper.


Step 2: Set Up the Core Strand and Metal Rings

The core strand holds the structural load of the turkey. You will mount the metal O-rings to this strand to establish the adjustable sliding loops.



  1. Fold your 6-foot core strand exactly in half to find its center point.
  2. Lay the folded cord flat on your work surface. Slide one metal O-ring onto the left side of the cord and the other metal O-ring onto the right side.
  3. Adjust the spacing so that you have a central "handle" section measuring approximately 8 inches. The two strands of the core must run parallel between the two metal rings.
  4. Secure each ring in place temporarily by tying a loose overhand knot just outside the 8-inch handle zone on both sides. This ensures your handle length remains consistent while you begin the weaving process.


Step 3: Align the Weaving Strand

The 16-foot weaving strand will be knotted over the two parallel core strands to build the handle.



  1. Find the exact midpoint of your 16-foot weaving strand.
  2. Slide this midpoint underneath the two parallel core strands at the far left edge of your designated 8-inch handle section, right next to the left O-ring.
  3. Ensure you have equal lengths of weaving cord extending to the left and right of the core strands (approximately 8 feet on each side).


Step 4: Braid the Cobra Weave Handle

The Cobra weave (also known as the Solomon bar) is the industry standard for paracord handles. It provides a flat, wide surface that prevents the heavy load of a harvested bird from digging into your hand.



  1. Form the First Loop: Take the left weaving strand and pass it over the top of the two central core strands, pointing toward the right. This creates a loop on the left side.
  2. Route the Right Strand: Take the right weaving strand and place it over the tail of the left strand that you just brought across.
  3. Thread Through the Loop: Pass the right weaving strand under the two central core strands, then bring it up through the loop on the left side from underneath.
  4. Tighten the Half-Knot: Pull both the left and right weaving strands outward with equal tension. Slide this first knot up tight against the left O-ring. Keep the core strands straight and flat.
  5. Alternate Sides to Form the Second Knot: Take the right weaving strand and lay it over the top of the central core strands to the left. Take the left weaving strand, place it over the tail of the right strand, run it under the central core strands, and pull it up through the loop on the right side. Tighten firmly.
  6. Repeat the Alternating Pattern: Continue this alternating pattern (Left-over-core, then Right-over-core) down the length of the 8-inch handle. You will notice a neat, ridged border forming on both sides of the flat handle.

Pro-Tip: Maintain uniform tension on every single knot. If you pull some knots tighter than others, the handle will twist and become uneven, which creates hot spots on your palm when carrying heavy game.



Step 5: Finish and Fuse the Handle Ends

Once your Cobra weave reaches the right O-ring, you must secure the weaving ends so they cannot unravel under field conditions.



  1. Ensure the final knot is packed extremely tight against the right O-ring.
  2. Using your heavy-duty shears, cut the remaining working ends of the weaving strand, leaving exactly 1/8th of an inch of cord sticking out from the side of the last braid. Do not cut the central core strands.
  3. Use the blue flame of your lighter to heat the 1/8th-inch protruding ends until they melt into dome-shaped liquid nylon beads.
  4. Immediately press the flat edge of your lighter metal casing or a cold knife blade against the molten nylon. Press firmly to flatten the melted bead against the surrounding weave, effectively welding the cord ends in place.

Warning: Avoid inhaling the fumes from the melting nylon, and do not touch the molten plastic with your bare skin, as it will cause severe contact burns.



Step 6: Create the Cinch Loops

With the handle completed, you now have two long core strands extending from each side of your braided handle, each routed through a metal O-ring.



  1. Untie the temporary safety knots you placed on the core strands in Step 2.
  2. Take the pair of core strands extending from the left side of the handle. Pass their ends through the center of the left metal O-ring from the bottom up.
  3. Tie a secure double overhand stopper knot at the very end of these two strands. Pull the knot extremely tight using pliers. This stopper knot prevents the ends from sliding back out through the O-ring.
  4. Repeat this process on the right side: pass the two right core strands through the right metal O-ring and tie a matching double overhand stopper knot.
  5. Singe the ends of the stopper knots with your lighter to ensure they never fray or slip loose under load. You now have two self-cinching loops. When you pull the handle upward, the weight of the bird tightens the loops around its legs.

Paracord Turkey Hunting Tote Sling - Etsy

Paracord Turkey Hunting Tote Sling - Etsy

Material Specifications & Cordage Performance

When choosing materials for hunting gear, understanding the engineering properties of your cordage ensures field reliability. Polyester, utility cord, and shock cord are unsuitable for heavy game transport. Use the table below to compare structural specifications.



Cordage Type Tensile Strength Core Construction Elasticity / Stretch Best Outdoor Application
Type III 550 Paracord (Nylon) 550 lbs 7 to 9 triple-ply inner yarns 30% elongation (excellent shock absorption) Game Totes, Lanyards, Emergency Rigging
Type IV 750 Paracord (Nylon) 750 lbs 11 triple-ply inner yarns 30% elongation Heavy big-game dragging, survival gear
Commercial Polyester Cord 225 - 300 lbs Braided core or loose fibers Very low (stiff, prone to knot slippage) Light utility wrapping, crafts
Mil-Spec C-5040H Paracord 550 lbs 7 triple-ply yarns (Govt. certified) 30%+ (highest mildew/UV resistance) Tactical gear, military use, heavy hauling

Field Failures & Heavy-Duty Maintenance

Even the most carefully crafted gear can encounter issues during a demanding hunt. Knowing how to diagnose and repair failures in the field is critical.



Issue 1: Cinch Loop Slippage (Game Slipping Out of the Tote)



  • Root Cause: The stopper knot at the end of the loop is too small, allowing it to pull through the metal O-ring, or the loop was placed around the turkey’s legs above the knuckle without proper tensioning.
  • Actionable Fix: Re-tie the stopper knot using a larger figure-eight knot or a double-overhand stopper knot. When securing a wild turkey, always place the cinch loop directly above the foot spur or joint, ensuring the weight of the bird pulls the loop tight against a structural bone flare.


Issue 2: Cord Fraying Near the Metal Rings



  • Root Cause: Using low-quality, non-welded, or stamped metal rings that have sharp inner burrs. The constant friction of the paracord sliding through the ring under load wears down the outer protective nylon sheath.
  • Actionable Fix: Wrap the section of the ring that contacts the cord with a small strip of heavy-duty electrical tape, or replace the rings with seamless, polished, marine-grade stainless steel O-rings.


Issue 3: Handle Rolling or Twisting



  • Root Cause: The Cobra weave was tied with unequal tension on the left and right sides, or you failed to alternate the starting side of the knot during construction.
  • Actionable Fix: Untie the handle wrap back to the twist point. Re-braid the section, making sure to alternate left and right over-loops strictly, and pull each knot tight with uniform force.

Frequently Asked Questions



How much weight can a paracord turkey tote safely carry?

A paracord turkey tote built with authentic Type III 550 paracord and welded steel rings can easily support over 150 pounds of static weight. However, the limit is typically determined by the comfort of the carrier’s hand; carrying more than two large turkeys (approx. 40 to 50 pounds total) on a single handle will cause noticeable hand strain over long distances.



Can I use this design to carry other types of game?

Yes, this sliding-cinch design is highly versatile. It works exceptionally well as a waterfowl game carrier for geese and ducks, a small game tote for rabbits and squirrels, or even a predator drag for coyotes.



What is the advantage of using metal rings over paracord-only loops?

Metal rings offer significantly less friction than nylon-on-nylon loops. This low friction allows the cinch loops to tighten instantly around the game's legs when lifted, and release effortlessly when the weight is set down. Nylon loops can bind or lock up, making it difficult to release the game with cold or gloved hands.



How do I clean dried blood and dirt off my paracord tote after a hunt?

Soak the tote in a bucket of warm water mixed with a mild dish soap for 30 minutes. Use a stiff-bristled nylon brush to scrub away dried blood, dirt, and organic matter from the woven handle. Rinse thoroughly with clean water and hang the tote to air-dry out of direct sunlight; do not use a clothes dryer, as extreme heat can shrink the nylon fibers unevenly.

Prepare for Your Next Harvest

Now that you have constructed a high-durability paracord turkey tote, you can head into the spring or fall woods with confidence in your gear. Keep this lightweight, heavy-duty carrier packed with your calls and decoys so you are ready to comfortably pack out your next hard-earned gobbler.


Paracord Turkey Tote - Etsy

Paracord Turkey Tote - Etsy

Read also: An unexpected early career for scott chambers has been discovered