How To Make An Electric Bike Go Faster: Technical Strategies For Peak E-Bike Performance

How To Make An Electric Bike Go Faster: Technical Strategies For Peak E-Bike Performance

How to Make an Electric Bike Faster (Safely): 10 Tips That Actually ...

Increasing the top speed of an electric bike requires bypassing factory-set electronic governors, optimizing the electrical system voltage, and reducing mechanical rolling resistance. By adjusting the controller's internal P-settings to increase the speed limit or upgrading to a higher-voltage battery, riders can achieve velocity increases of 20% to 50% depending on the motor’s watt-hour capacity and heat dissipation limits.


Technical Readiness and Performance Optimization Checklist

Before attempting to modify an electric bike's speed parameters, it is critical to understand that most consumer e-bikes are restricted by regional regulations, such as the 20 mph (32 km/h) limit for Class 1 and 2 bikes in the United States or the 25 km/h limit in the European Union. Modifying these limits often transitions the vehicle into a different legal category, potentially requiring registration or restricting use to private land. Furthermore, increasing speed places higher thermal stress on the Brushless DC (BLDC) motor and the Battery Management System (BMS).



  • Essential Technical Tools: Multimeter for voltage testing, soldering iron (for shunt modifications), hex key set (2mm to 8mm), and a laptop with a USB-to-TTL serial adapter if your controller supports software programming.
  • Safety Upgrades: High-performance hydraulic disc brakes with 180mm or 203mm rotors, heat-dissipating brake pads, and tires rated for speeds exceeding 30 mph.
  • Required Knowledge: Basic understanding of Ohm’s Law ($V = I \times R$), familiarity with Pulse Width Modulation (PWM) signals, and the ability to navigate LCD interface menus.
  • Estimated Investment: Software tweaks and sensor adjustments are often free, while battery and controller upgrades can range from $300 to $1,200.
  • Time Commitment: 30 minutes for software/sensor changes; 3 to 5 hours for hardware component swaps.

Engineering Enhanced Velocity: A Systematic Approach to E-Bike Speed Modification

Achieving higher speeds involves a tiered approach, starting with non-invasive software adjustments and moving toward advanced hardware engineering. Each step increases the potential for heat generation, so incremental testing is mandatory to prevent permanent motor failure.



Step 1: Adjusting Software Limits via the Display Interface

Most modern e-bikes utilize an LCD or LED display that communicates with the motor controller via a serial protocol. Manufacturers include "P-settings" (Parameter settings) that dictate wheel size and speed limits.



  1. Access the settings menu by holding the "Up" and "Down" buttons or the "Power" and "Up" buttons simultaneously for several seconds.
  2. Navigate to the speed limit setting, typically labeled as P08 on many common controllers (like those from Bafang or SW900).
  3. Increase the value to the maximum (often 100 km/h or 62 mph) to effectively remove the electronic governor.
  4. Optionally, reduce the programmed wheel size. By convincing the controller that the wheel is smaller than it actually is (e.g., setting it to 20 inches when it is 26 inches), the controller will spin the motor faster to reach what it perceives as the legal limit. Note that this will result in an inaccurate speedometer reading.

Pro-Tip: If your display is locked by a password, search for common manufacturer codes such as 1919, 1199, or 0512.



Step 2: Physical Speed Sensor Manipulation

Many e-bikes calculate speed using a magnet attached to a spoke and a hall-effect sensor mounted on the frame. When the magnet passes the sensor, it completes a circuit, telling the controller how fast the wheel is turning.



  1. Locate the speed sensor on the chainstay and the magnet on the spoke.
  2. Relocate the sensor so it faces the crank arm instead of the wheel.
  3. Move the magnet to the crank arm. Now, the controller measures your pedaling cadence rather than your wheel speed. Since you pedal much slower than the wheel spins, the controller never hits the programmed speed limit, allowing the motor to provide assistance up to its physical RPM limit.

Warning: This modification disables the speedometer and may cause "error codes" on mid-drive systems like Bosch or Shimano that compare motor RPM to wheel RPM.



Step 3: Increasing System Voltage and Battery Upgrades

Voltage is directly proportional to the maximum RPM of a BLDC motor, a relationship defined by the motor’s KV rating (RPM per volt). If a 36V system reaches 20 mph, a 48V system will theoretically reach approximately 26-28 mph on the same motor.



  1. Verify the maximum voltage rating of your controller’s internal capacitors and MOSFETs. A "36V" controller can often handle a 48V battery if the capacitors are rated for 63V.
  2. Replace the existing battery pack with one of a higher nominal voltage.
  3. If the controller is not compatible with higher voltage, you must replace both the battery and the controller simultaneously.
  4. Ensure the new Battery Management System (BMS) can handle the continuous amperage draw required for sustained high-speed operation.


Step 4: The Controller Shunt Modification

The "Shunt Mod" is a hardware hack that increases the current (amps) the controller allows to flow to the motor. While voltage increases top speed, amperage increases torque and the ability to maintain speed under load or on inclines.



  1. Open the motor controller housing to reveal the circuit board.
  2. Locate the shunt, which looks like one or more thick, U-shaped wires (usually made of manganin).
  3. Apply a small amount of solder to a portion of the shunt wire. This reduces the shunt's resistance.
  4. Because the controller measures current based on the voltage drop across this resistance, the reduced resistance "tricks" the controller into thinking it is drawing less current than it actually is, causing it to push more power to the motor.

Warning: Over-soldering the shunt can lead to catastrophic MOSFET failure or motor burnout due to excessive heat. Monitor motor casing temperatures closely during the first test ride.



Step 5: Optimizing Mechanical Efficiency

Aerodynamic drag and rolling resistance are the primary forces opposing your motor at speeds above 20 mph. At 30 mph, roughly 80% of your energy is spent simply pushing through the air.



  1. Increase tire pressure to the maximum PSI recommended on the sidewall to minimize the tire's contact patch.
  2. Switch from knobby off-road tires to smooth, "slick" tires.
  3. Lubricate the drivetrain with high-efficiency ceramic wax to reduce friction in the chain and derailleur pulleys.
  4. Adjust your riding posture; tucking your elbows and lowering your torso can add 1-3 mph to your top speed without any electrical modifications.

How Can I Make My Electric Bike Go Faster? - REVIBIKES

How Can I Make My Electric Bike Go Faster? - REVIBIKES

Comparative Performance Metrics for Voltage and Gearing

The following table illustrates the theoretical speed gains when modifying the electrical and mechanical parameters of a standard 750W hub motor system.



Modification Variable Baseline (36V System) Upgraded (48V System) High Performance (52V+)
Top Speed (Flat Ground) 18 - 20 mph 24 - 28 mph 30 - 35+ mph
Acceleration (0-20 mph) 8.5 Seconds 5.2 Seconds 3.8 Seconds
Controller Current (Amps) 15A - 18A 20A - 25A 30A - 45A
Wattage (Peak) 648W 1200W 1800W+
Thermal Risk Factor Low Moderate High
Recommended Gear Ratio 44T Front / 14T Rear 48T Front / 12T Rear 52T Front / 11T Rear

Common Failure Scenarios and Technical Fixes

Modifying an e-bike beyond its factory specifications introduces several common failure points. Identifying these early can prevent expensive hardware replacements.



  • Scenario: Motor "Stuttering" or Cogging Under Heavy Load



    • Root Cause: Blown MOSFETs in the controller or a melted phase wire connector. When the controller is pushed to higher Amps via a shunt mod, the heat can melt the plastic "bullet" connectors.
    • Actionable Fix: Replace plastic connectors with high-current MT60 or XT90 connectors. Inspect the controller for charred components and replace the MOSFETs with higher-rated versions (e.g., IRFB4110).
  • Scenario: The Bike Shuts Off Abruptly at Full Throttle



    • Root Cause: The Battery Management System (BMS) Over-Current Protection (OCP) is triggering. The battery cannot safely provide the amperage requested by the modified controller.
    • Actionable Fix: Install a BMS with a higher continuous discharge rating or add a second battery pack in parallel to split the current load.
  • Scenario: Significant Speed Drop After 5 Minutes of Riding



    • Root Cause: Thermal throttling or "Voltage Sag." As the battery is pushed hard, internal resistance causes the voltage to drop, which reduces RPM.
    • Actionable Fix: Use high-discharge cells (like Samsung 25R or Molicel P42A) in your battery pack construction to minimize sag. Improve motor cooling by adding "Statorade" (ferrofluid) to the hub motor to bridge the air gap and dissipate heat to the casing.

Frequently Asked Questions



Will making my e-bike faster decrease its lifespan?

Yes, increasing speed increases the RPM and heat within the motor windings and the controller. Over time, this can degrade the insulation on the copper windings or wear out internal nylon gears in geared hub motors faster than at stock speeds.



Can I upgrade just the battery without changing the controller?

It depends on the controller's voltage ceiling. Most 36V controllers have 50V or 63V capacitors, meaning they can handle a 48V battery (which charges to 54.6V), but 52V batteries may exceed the safety margin and blow the capacitors.



Does removing the speed limiter void the warranty?

Almost certainly. Most manufacturers use controllers that log peak speeds or have "tamper-evident" seals. Modifying the firmware or cutting the speed-limiting wire will typically void all claims related to the electrical system.



Why does my bike feel slower even after modifications?

If you increase the electrical speed but do not change the mechanical gearing, you may be "ghost pedaling." If your legs cannot keep up with the motor's speed, you lose the additive power of your pedaling, which can make the bike feel less responsive at the top end.

Optimize Your Ride Safely

While extracting more speed from an electric bike is a rewarding technical challenge, always prioritize structural integrity and braking power to match your new velocity. Ensure your tires, spokes, and braking systems are rated for the increased kinetic energy associated with high-speed travel.


How To Build Electric Motor Bike at Caitlin Kelley blog

How To Build Electric Motor Bike at Caitlin Kelley blog

Read also: Smart tracking will soon replace the printed 272 bus timetable