How To Install Trucks On A Skateboard: A Step-by-Step Assembly Guide
To install trucks on a skateboard, insert eight mounting bolts through the top of the deck, align the trucks with the kingpins facing inward toward each other, and secure them with locknuts. Use a skate tool or a combination of a screwdriver and a 3/8-inch wrench to tighten the hardware in a cross-pattern until the bolt heads sit perfectly flush with the grip tape. Ensuring proper orientation and tension prevents mechanical failure and guarantees predictable steering response.
Skateboard Anatomy & Assembly Preparation
Assembling a skateboard requires precise alignment and torque to ensure the board handles correctly and remains structurally sound. Skateboard decks are traditionally constructed from seven plies of laminated hard rock maple, which can crack or warp if mounting hardware is unevenly tensioned. Before beginning the physical installation, you must understand the component anatomy and gather the specific tools required for a professional-grade assembly.
Technical Components Checklist
- Skateboard Deck: Ensure your deck is fully gripped. If you have just applied grip tape, ensure the edges are filed down and trimmed clean before mounting the hardware.
- Skateboard Trucks (Set of 2): Consists of the baseplate, hanger, kingpin, bushings, and washers.
- Mounting Hardware: Eight high-tensile bolts (typically No. 10-32 UNF threads) and eight matching nylon-insert locknuts (Nyloc). Bolt lengths generally range from 7/8 inch to 1 inch for standard setups.
- Riser Pads (Optional): Hard plastic or rubber pads placed between the deck and baseplate to increase clearance and prevent wheel bite.
- Multi-Purpose Skate Tool: A specialized T-tool containing a 3/8-inch socket (for hardware nuts), a 1/2-inch socket (for axle nuts), a 9/16-inch socket (for the kingpin nut), and an integrated Phillips/Allen driver.
- Alternative Hand Tools: If a skate tool is unavailable, use a standard #2 Phillips-head screwdriver (or 1/8-inch Allen key, depending on your hardware type) and a 3/8-inch open-ended wrench or socket wrench.
Estimated Assembly Benchmarks
- Difficulty Level: Beginner
- Time Required: 10 to 15 minutes
- Required Budget: $5 to $15 (assuming you already own the deck, trucks, and wheels, and only need to purchase mounting hardware and a basic tool).
Step-by-Step Skateboard Truck Installation
Step 1: Puncture the Grip Tape Holes
Most fresh grip tape jobs completely cover the eight pre-drilled mounting holes in your skateboard deck. To insert the bolts, you must first locate and puncture these holes from the underside of the board.
- Flip the skateboard deck over so the graphic side is facing up and the black grip tape side is resting on your work surface.
- Take a spare mounting bolt, an Allen key, or a small Phillips screwdriver, and push it firmly upward through one of the pre-drilled holes from the bottom of the board.
- Push hard enough to create a small protrusion or bubble on the grip tape side. Repeat this process for all eight holes.
- Flip the deck grip-side up. Use your screwdriver to push downward through the newly created bubbles. Twist the tool slightly to clear out any excess grip tape debris inside the hole, ensuring a clean passageway for the hardware.
Pro-Tip: Pushing the bolts through from the top down without clearing the grip tape first can cause the grip tape to bunch up, tear, or prevent the bolt head from sitting flush with the deck surface.
Step 2: Insert the Mounting Hardware
With the holes cleared, you will now insert the bolts through the top of the deck.
- Place the skateboard deck flat on your work surface with the grip tape facing upward.
- Insert all eight bolts into the holes, pointing straight down through the wood.
- Push them down until the threaded ends protrude through the bottom (graphic side) of the board.
Warning: If you are using colored or specialty "directional" bolts to help identify the nose and tail of your skateboard, ensure you place them in the front two holes of the front truck nose area before proceeding.
Step 3: Align the Trucks with Correct Orientation
Improper truck orientation is the most common assembly error made by beginners. Skateboard trucks are engineered with specific steering geometry. Installing them backward will cause the board to turn in the opposite direction of your weight distribution, making riding nearly impossible.
- Flip the deck over or hold it sideways so the threaded bolts point upward.
- If you are using riser pads, slide them over the bolts first, flat against the wood of the deck.
- Lower the first truck onto the four protruding bolts.
- Verify Kingpin Direction: For standard skateboard trucks (traditional kingpin or TKP), the large kingpins (the central bolts holding the hanger and bushings) must face inward, pointing toward each other at the center of the board. The solid outer edges of the hangers must face outward toward the nose and tail.
- If you are assembling a longboard with reverse kingpin (RKP) trucks, the rule is reversed: the kingpins must face outward toward the nose and tail of the board.
Warning: Double-check your orientation before tightening. If the kingpins on standard trucks face outward toward the kicktails, your skateboard will steer backward, creating an immediate safety hazard.
Step 4: Hand-Tighten the Locknuts
Securing the hardware by hand prevents cross-threading and ensures the bolts do not push back out of the deck during the initial tool-tightening phase.
- While holding the truck baseplate flat against the deck with one hand, thread a nylon-insert locknut onto the end of each bolt using your fingers.
- Spin the nuts clockwise until the nylon ring inside the nut contacts the threads of the bolt.
- Repeat this for all four bolts on the current truck, then repeat the alignment and hand-tightening process on the second truck.
Step 5: Tighten Hardware in a Cross-Pattern
To prevent warping the cast aluminum truck baseplate or splitting the wood plies of your deck, you must tighten the hardware gradually using a diagonal cross-pattern, identical to how you would tighten the lug nuts on a car wheel.
- Insert your Phillips screwdriver or Allen key into the bolt head on the top (grip tape) side of the deck and hold it completely still.
- Fit your 3/8-inch socket or skate tool onto the corresponding locknut on the bottom side.
- Turn the nut clockwise to tighten. Always turn the nut rather than spinning the bolt; spinning the bolt head inside the grip tape can strip the head or tear the tape.
- Tighten the first nut until it is snug but not fully clamped.
- Move diagonally to the opposite corner nut and tighten it. Next, tighten the third nut, followed by the final diagonal nut.
- Return to the first nut and repeat the sequence, tightening each bolt until the head of the bolt sits perfectly flush with the grip tape surface.
Pro-Tip: Do not over-tighten the hardware. The bolt head should sink slightly into the grip tape so it is level with the deck, but it should not crush deep into the top wooden ply of the skateboard, which can cause pressure cracks.
Step 6: Perform a Tolerance and Steering Test
Once both trucks are fully mounted, perform a quick mechanical clearance check before taking the board to the pavement.
- Set the skateboard on its wheels on a flat surface.
- Stand on the board and lean heavily from side to side. Watch the underside of the deck to check if the wheels touch the wood during deep turns.
- If the wheels contact the wood (known as wheel bite), you must either tighten your kingpin nut to stiffen the steering, install thicker riser pads, or swap to smaller wheels.
Bulk Skateboard Trucks at Geri Hodge blog
Skateboard Hardware, Riser, and Truck Sizing Matrix
To choose the correct hardware length for your specific board configuration, refer to the technical specifications below. Using bolts that are too short will prevent the nylon locknut from engaging, while bolts that are too long create drag hazards and look unprofessional.
| Hardware Length | Riser Pad Thickness | Compatible Wheel Diameter | Optimal Skateboard Use Case |
|---|---|---|---|
| 7/8 Inch | No Riser | 48mm to 53mm | Street, technical park skating with low/mid trucks. |
| 1.0 Inch | No Riser to 1/8 Inch | 52mm to 56mm | All-around transition, bowl, and street skating. |
| 1.125 Inches | 1/8 Inch | 54mm to 58mm | Cruisers and transition boards requiring moderate wheel clearance. |
| 1.25 Inches | 1/4 Inch | 56mm to 62mm | Large-wheel cruisers and filmer boards using medium risers. |
| 1.5 Inches | 1/2 Inch | 60mm to 70mm | Longboarding, deep carving, and downhill setups with thick risers. |
Common Installation Mistakes and Quick Field Fixes
The Board Steers Backward or Feels Extremely Unstable
- Root Cause: One or both of your skateboard trucks have been installed backward, meaning the kingpins are facing the wrong direction.
- Actionable Fix: Use your skate tool to completely remove the four locknuts on the affected truck. Pull the truck off the bolts, rotate it 180 degrees so that standard kingpins face inward toward the center of the board, slide it back onto the bolts, and re-tighten the nuts in a diagonal pattern.
Squeaking Noise When Leaning Side-to-Side
- Root Cause: Friction between the polyurethane bushings or pivot cup and the raw metal of the truck baseplate hanger.
- Actionable Fix: Remove the kingpin nut, washers, and bushings. Shave a few small flakes of dry paraffin wax or bar soap into the empty pivot cup and onto the contact surfaces of the polyurethane bushings. Reassemble the truck; the wax acts as a dry lubricant, permanently eliminating the squeak without degrading the polyurethane.
Hardware Spins Infinitely Without Tightening
- Root Cause: The bolt head has stripped the surrounding grip tape and wood, or the threads on the bolt and nut have cross-threaded.
- Actionable Fix: Securely clamp the outer rim of the locknut with locking pliers (Vise-Grip) to keep it from spinning. Insert your screwdriver firmly into the bolt head from above, applying heavy downward pressure, and turn counterclockwise to force the damaged nut off. Replace the stripped bolt and nut with fresh No. 10-32 hardware.
Frequently Asked Questions
Which way do skateboard trucks face?
For standard street and park skateboards, the kingpins (the large central bolts holding the bushings) must face inward toward the center of the board. For reverse kingpin (RKP) trucks, which are standard on downhill and carving longboards, the kingpins must face outward toward the nose and tail.
How tight should skateboard truck bolts be?
Skateboard mounting bolts should be tightened until the heads are sitting flush with the top of your grip tape. If the bolt heads stick up, they will interfere with your foot placement; if they are sunk deep into the wood, they will cause structural pressure cracks around the mounting holes.
Do I need riser pads for my skateboard?
Riser pads are not necessary if you are riding wheels smaller than 54mm on standard-height trucks. However, if you are using wheels 55mm or larger, installing 1/8-inch or 1/4-inch riser pads is highly recommended to prevent wheel bite, which can cause the board to stop abruptly during sharp turns.
What size socket wrench fits skateboard mounting hardware?
Standard skateboard mounting hardware uses a 3/8-inch nut, which requires a 3/8-inch socket wrench or the smallest opening on a standard skateboard T-tool. The bolts themselves typically require either a #2 Phillips head screwdriver or a 1/8-inch Allen wrench.
Elevate Your Skateboard Setup Today
Now that your trucks are securely mounted and mathematically aligned, you are ready to fine-tune your steering and take your riding to the next level. Browse our premium selection of high-rebound bushings, heavy-duty hardware, and professional-grade skate tools to keep your setup rolling smoothly.