Comprehensive Guide: How To Install Asphalt Roll Roofing For Low-Slope Structures
Installing asphalt roll roofing is an efficient, cost-effective solution for low-slope structures, requiring precise edge sealing and consistent adhesive application to prevent water infiltration. By adhering to a minimum slope requirement of 2:12 and ensuring a clean, dry substrate, professional-grade results are achievable through careful material overlapping and proper fastener spacing.
Essential Preparation and Installation Requirements
Asphalt roll roofing is designed specifically for flat or low-slope roofs, such as sheds, porches, or garages with a slope between 2:12 and 4:12. Attempting to install this material on roofs with steeper pitches often results in slippage and premature material failure. Before starting, ensure the weather forecast remains clear for at least 48 hours, as ambient temperatures between 50 and 80 degrees Fahrenheit are critical for the material to unroll without cracking and for the adhesive to cure properly.
Essential Tools and Equipment
Roofing hammer or pneumatic coil nailer
Utility knife with a supply of hook blades for precise cuts
Chalk line for maintaining alignment
Roofing cement (plastic cement) applied via trowel or caulking gun
Galvanized roofing nails (1-inch to 1.25-inch)
Heavy-duty work gloves and slip-resistant footwear
Safety harness and roof anchors for working at elevation
Tape measure and carpenter’s square
Prerequisites and Standards
Ensure the roof deck (typically 1/2-inch OSB or plywood) is free of rot, protrusions, and debris.
Verify the moisture content of the wood deck is below 19% to prevent future warping.
Calculate material requirements by determining the total surface area and adding a 15% margin for overlaps and waste.
Inspect the perimeter to ensure drip edges are installed to facilitate water drainage away from the fascia boards.
Systematic Installation Workflow for Asphalt Roofing
Step 1: Laying the Underlayment
Begin by installing a layer of roofing felt or synthetic underlayment over the entire roof deck. This acts as a secondary moisture barrier. Secure the underlayment with plastic-capped nails spaced every 12 inches along the edges and every 24 inches in the field. Ensure that each subsequent row overlaps the one below by at least 4 inches.
Step 2: Measuring and Positioning the Starter Strip
Cut a strip of the asphalt roll roofing approximately 18 inches wide to serve as the starter strip. Align this along the eaves of the roof. Secure the starter strip with nails spaced 6 inches apart along the bottom edge, ensuring the edge of the roll overhangs the drip edge by approximately 1/2 inch to 3/4 inch to ensure proper runoff.
Step 3: Rolling and Aligning the Main Sheets
Unroll the asphalt roofing, positioning the first full-width sheet over the starter strip. Allow the material to relax for at least 30 minutes before final alignment. Align the edge of the sheet parallel to the eaves. If your product features a factory-applied adhesive strip, ensure this edge faces uphill.
Warning: Do not force the material to lay flat if it is cold. The material will become brittle and crack. If the environment is below 50 degrees Fahrenheit, allow the rolls to sit in a heated area before deployment.
Step 4: Applying Adhesive and Securing the Sheet
Apply a 4-inch wide strip of asphalt roofing cement to the area where the sheets overlap. Press the overlapping sheet firmly into the wet cement. Use a weighted roller or press firmly by hand to ensure a complete bond. Secure the upper edge of each sheet with roofing nails spaced every 8 to 10 inches.
Step 5: Sealing the Perimeter and Seams
After laying all sheets, apply a bead of roofing cement to all exposed nail heads. For the top edge where the roof meets a wall or chimney, install metal flashing and secure it with plastic cement, ensuring the flashing overlaps the roofing material by at least 6 inches to prevent capillary water action.
How to Install Asphalt Roofing Roll: 2026 DIY Guide
Technical Specifications and Material Performance Metrics
| Parameter | Specification | Tolerance/Requirement |
|---|---|---|
| Minimum Roof Slope | 2:12 | Must exceed 2-inch rise per foot |
| Nail Spacing (Field) | 8-10 inches | Consistent pattern required |
| Lap Overlap | 4 inches | Minimum for watertight seal |
| Fastener Type | Galvanized Roofing Nails | 11-gauge shank, 3/8-inch head |
| Ambient Temp Range | 50°F – 80°F | Optimal for material pliability |
Troubleshooting Common Installation Failures
- Root Cause: Bubbles or "Fish-mouths" appearing in the field.
- Actionable Fix: Often caused by trapped air or moisture. Cut a small slit in the center of the bubble, press the material flat, insert roofing cement underneath, and nail the perimeter of the patch before sealing the surface with more cement.
- Root Cause: Leaks at the eaves or gable edges.
- Actionable Fix: This is usually due to improper drip edge integration. Ensure the drip edge is installed under the underlayment at the eaves but over the underlayment at the rakes. Replace damaged sections and re-seal with cement.
- Root Cause: Material sliding or tearing at fasteners.
- Actionable Fix: This indicates that the slope is too steep or the fasteners were driven too deep into the substrate. Install a cleat or stop at the roof edge and ensure nails are driven flush with the surface rather than punched through the mineral coating.
Frequently Asked Questions
Can I install asphalt roll roofing over existing shingles?
It is not recommended. Installing new roll roofing over existing shingles traps moisture, accelerates deck decay, and creates an uneven surface that will cause the roll roofing to crack and tear under thermal expansion.
How long does a roll roofing installation last?
Typically, asphalt roll roofing has a lifespan of 5 to 10 years, depending on the thickness of the product, local weather conditions, and how effectively the seams were sealed during installation.
Do I need to use a primer before applying roofing cement?
Generally, no, provided the surface is clean and dry. However, if the surface is porous or aged, applying a thin coat of asphalt primer can improve the adhesion of the roofing cement and the roll itself.
How do I handle valleys or chimney penetrations?
Use reinforced flashing fabric embedded in roofing cement for these areas. Never fold a single sheet of roll roofing through a valley; instead, terminate sheets on either side of the valley and cover the transition with a separate strip of membrane flashing.
Consult with local building codes regarding specific fire ratings for roofing materials in your jurisdiction to ensure your installation meets all safety compliance standards.