How To Increase PH In A Pool: A Professional Guide To Balancing Water Chemistry

How To Increase PH In A Pool: A Professional Guide To Balancing Water Chemistry

What is the proper pool pH and how to get it | ARM & HAMMER™

To increase pH in a swimming pool, the most effective method is adding sodium carbonate (soda ash) to the water while the filtration system is running. Maintaining a target pH range between 7.4 and 7.6 ensures optimal sanitizer efficacy, prevents equipment corrosion, and eliminates eye irritation for swimmers.


Chemical Analysis and Essential Maintenance Equipment

Maintaining a pool’s pH is a foundational task in water chemistry management. The potential of Hydrogen (pH) is a logarithmic scale from 0 to 14 that measures the acidity or alkalinity of the water. When pool water falls below 7.2, it becomes acidic, leading to the corrosion of metal components like heat exchangers, the etching of plaster surfaces, and the rapid degradation of chlorine. Before attempting to adjust the chemical balance, you must gather precise data and the correct materials to avoid "chemical chasing," where overcorrection leads to a see-saw effect in water stability.



Essential Gear and Chemical Requirements



  • Professional Test Kit: Use a DPD (N,N-diethyl-p-phenylenediamine) liquid test kit or a high-quality digital photometer. Avoid basic test strips for corrective dosing as they lack the precision needed for accurate calculations.
  • Sodium Carbonate (Soda Ash): The primary chemical used to raise pH. It has a high pH (around 11.4) and effectively raises pH with a moderate impact on Total Alkalinity.
  • Sodium Bicarbonate (Baking Soda): Used primarily if both pH and Total Alkalinity are low. It has a much lower pH (8.3) and is better suited for stabilizing pH by raising alkalinity.
  • Protective Gear: Chemical-resistant gloves and safety goggles are mandatory when handling concentrated soda ash to prevent skin irritation and eye damage.
  • Plastic Five-Gallon Bucket: Required for pre-dissolving chemicals to prevent staining of the pool floor and to ensure even distribution.
  • Measuring Scale or Scoop: Accurate measurements in ounces or grams are critical; never "eyeball" chemical dosages.


Benchmarks for Success



  • Ideal pH Range: 7.4 to 7.6
  • Total Alkalinity Range: 80 to 120 parts per million (ppm)
  • Circulation Time: 4 to 6 hours after application before re-testing.
  • Budget Benchmark: $15 – $40 for basic chemical supplies.

Systematic Workflow for Raising Pool pH

Successful pH adjustment requires a methodical approach that accounts for the pool’s volume and current chemical state. Following these steps ensures the water reaches equilibrium without overshooting the target and causing scaling or cloudiness.



Step 1: Baseline Chemical Testing and Volume Calculation

Before adding any chemicals, you must know the exact volume of your pool in gallons or liters and the current pH level. Take a water sample from at least 18 inches below the surface, away from the return jets.



  1. Rinse the test vial in the pool water first.
  2. Add the specified number of Phenol Red drops (usually 5) to the pH chamber.
  3. Compare the color against the standard scale in natural light.
  4. Simultaneously test for Total Alkalinity (TA). If TA is below 80 ppm, you should address alkalinity first, as pH will be unstable and difficult to lock in without proper "buffering."


Step 2: Calculate the Required Dosage

The amount of soda ash needed depends on how far the pH has drifted from the target. A general rule of thumb for sodium carbonate is that 6 ounces will raise the pH of 10,000 gallons of water by approximately 0.1 units.



  1. Identify the delta (the difference between your current pH and your target of 7.5).
  2. Consult a chemical dosing chart or use the table provided later in this guide to determine the weight of the product required.
  3. Pro-Tip: Always aim for the lower end of the calculation. It is significantly easier to add more chemical later than it is to lower the pH once it has been overshot.


Step 3: Pre-Dissolving and Application

Never pour dry soda ash directly into the pool, especially in vinyl-liner or fiberglass pools, as the concentrated powder can settle on the bottom and cause bleaching or surface damage.



  1. Fill a five-gallon plastic bucket three-quarters full with pool water.
  2. Slowly add the measured amount of soda ash to the water (never add water to the chemical).
  3. Stir with a wooden or plastic stirrer until the powder is fully dissolved and the water is clear or slightly cloudy but without clumps.
  4. Turn on the pool’s circulation system to its highest setting.
  5. Walk around the perimeter of the pool, slowly pouring the mixture into the water, focusing on the deep end and avoiding the skimmer intake.

Warning: Do not add soda ash directly into the skimmer. This can cause a high-pH spike within the filtration system, leading to calcium scaling on the filter media or salt chlorine generator cells.



Step 4: Circulation and Verification

Water chemistry does not change instantaneously. The chemicals must be integrated into the entire body of water through active filtration.



  1. Keep the pump running for at least 4 to 8 hours to ensure a complete turnover of the pool water.
  2. Wait a minimum of 6 hours before re-testing the pH. For large commercial pools, waiting 24 hours provides the most accurate reading.
  3. Check the pH again using the Phenol Red test. If the pH is still below 7.2, repeat the dosage calculation and application process.

How to Raise pH in Pool: 12 Steps (with Pictures) - wikiHow

How to Raise pH in Pool: 12 Steps (with Pictures) - wikiHow

Soda Ash Dosage and Material Specifications

The following table outlines the standard dosage of Sodium Carbonate (Soda Ash) required to raise pH levels based on pool volume. These figures assume a standard Total Alkalinity level of 100 ppm.



Pool Volume (Gallons) To Raise pH by 0.2 (e.g., 7.0 to 7.2) To Raise pH by 0.4 (e.g., 6.8 to 7.2) To Raise pH by 0.6 (e.g., 6.6 to 7.2)
1,000 0.75 oz 1.5 oz 2.25 oz
5,000 4 oz 8 oz 12 oz
10,000 8 oz 16 oz (1 lb) 24 oz (1.5 lbs)
15,000 12 oz 24 oz (1.5 lbs) 36 oz (2.25 lbs)
20,000 16 oz (1 lb) 32 oz (2 lbs) 48 oz (3 lbs)
30,000 24 oz (1.5 lbs) 48 oz (3 lbs) 72 oz (4.5 lbs)
50,000 40 oz (2.5 lbs) 80 oz (5 lbs) 120 oz (7.5 lbs)

Common Chemistry Failures and Professional Fixes

In the field, adjusting pH is rarely a linear process. External factors like heavy rain, high bather load, and aeration can disrupt the balance. Below are the most frequent issues encountered during pH adjustment.



  • The "pH Bounce" Phenomenon



    • Root Cause: This occurs when Total Alkalinity is too low (below 80 ppm). Without enough bicarbonate ions to buffer the water, the pH becomes highly sensitive and will "bounce" or swing wildly with even small chemical additions.
    • Actionable Fix: Test and raise Total Alkalinity to 100 ppm using sodium bicarbonate before attempting further pH adjustments. This locks the pH in place.
  • Immediate Water Cloudiness After Addition



    • Root Cause: Adding soda ash too quickly or in too high a concentration can cause "localized precipitation." The high pH at the injection point causes calcium to fall out of suspension, creating a milky cloud.
    • Actionable Fix: Ensure the pump is running at high RPM. Pre-dissolve the chemical more thoroughly in a larger volume of water and distribute it across a wider area of the pool surface. If cloudiness persists, check the Calcium Hardness levels.
  • pH Refuses to Rise Despite Repeated Dosing



    • Root Cause: This usually indicates extremely low Cyanuric Acid (CYA) levels or a very high concentration of acidic sanitizers (like Trichlor pucks) that are constantly driving the pH down. It can also be caused by heavy rainfall, which is naturally acidic.
    • Actionable Fix: Check the pH of your fill water and examine your primary sanitizer. If you are using Trichlor pucks, consider switching to Liquid Chlorine (Sodium Hypochlorite), which has a high pH and will help maintain alkalinity rather than deplete it.
  • High pH with Corrosive Symptoms



    • Root Cause: This is a failure of the Langelier Saturation Index (LSI). The pH might look "correct" on a test, but if the Calcium Hardness and Alkalinity are very low, the water is still "hungry" and corrosive.
    • Actionable Fix: Use an LSI calculator. Adjust Calcium Hardness to at least 200-400 ppm to ensure the water is balanced, even if the pH is on the higher end of the scale.

Frequently Asked Questions



Can I use baking soda instead of soda ash to raise pH?

Yes, but it is less efficient for pH alone. Baking soda (sodium bicarbonate) has a pH of 8.3 and is primarily used to increase Total Alkalinity; while it will raise pH slightly, you would need significantly more of it compared to soda ash to achieve the same result.



How soon can I swim after adding soda ash to the pool?

You should wait at least 30 to 60 minutes after adding soda ash before swimming. This allows the chemical to disperse and the pH to equalize throughout the pool, preventing localized areas of high alkalinity that could cause skin or eye irritation.



Why does my pool pH keep dropping?

The most common reasons for a falling pH are the use of acidic chlorine tablets (Trichlor), heavy rainfall, and the introduction of organic contaminants like leaves or sweat. Additionally, if the Total Alkalinity is low, the pH will naturally drift downward over time.



Will high pH make my pool water cloudy?

Yes, if the pH rises above 7.8, it can cause calcium to precipitate out of the water, leading to a cloudy or "milky" appearance. This is especially common in areas with high Calcium Hardness or when soda ash is added too rapidly without proper circulation.



Does aeration increase pool pH?

Aeration is a natural way to raise pH without affecting Total Alkalinity. By using water features, fountains, or turning up return jets to create bubbles, you encourage carbon dioxide to off-gas from the water, which naturally causes the pH to rise.

Optimize Your Pool Chemistry Strategy

Mastering the balance of pH and alkalinity is the most effective way to protect your pool investment and ensure swimmer comfort. Regularly monitor your chemical levels and keep a stock of soda ash on hand to address acidity before it causes permanent damage to your equipment.


How to Test, Raise, and Lower Swimming Pool pH Level | Swimming pools ...

How to Test, Raise, and Lower Swimming Pool pH Level | Swimming pools ...

Read also: Advanced drone tech will soon assist the calhoun county sheriff department