How To Get Water Off A Pool Cover: A Complete Step-by-Step Removal Guide
Standing water on a pool cover must be removed using a specialized submersible cover pump or a gravity-fed siphon to prevent structural cover collapse, drowning hazards, and dirty water contamination. Aim to clear the cover whenever the water accumulation exceeds a depth of two inches, always discharging the runoff far from the pool deck and house foundation. Maintaining a dry, debris-free cover preserves the tension of safety springs and prevents expensive winter cover damage.
Pre-Operation Inspection and Equipment Checklist
Allowing water to pool on your winter pool cover creates severe mechanical risks. A standard 15-by-30-foot solid pool cover holding just two inches of standing water carries approximately 560 gallons of water. At 8.34 pounds per gallon, this equates to more than 4,600 pounds of dead weight pulling on your cover's anchor points, pool walls, or top rails. If left unchecked, this load can warp pool frames, snap brass safety anchors, tear vinyl liners, or cause the cover to slip entirely into the pool, dumping toxic, stagnant water into your balanced pool water.
Before attempting to clear the cover, you must determine whether you have a solid cover or a mesh safety cover. Solid vinyl or polyethylene covers are completely impermeable and require active, manual pumping. Mesh covers are designed to let water drain through into the pool while keeping large debris out, but they can still accumulate water if the mesh pore spaces become clogged with fine silt, decomposed leaves, or organic algae growth.
Gather the following professional-grade tools and safety equipment before beginning the water removal process:
- Submersible Pool Cover Pump: A 1/4 to 1/3 Horsepower (HP) electric pump rated between 1,200 and 1,800 Gallons Per Hour (GPH). Choose an automatic sensor pump to prevent the motor from running dry.
- Heavy-Duty Garden Hose or Discharge Hose: A 3/4-inch diameter garden hose or a 1-1/4-inch lay-flat discharge hose, measuring at least 50 to 100 feet to safely route water away from the pool area.
- Telescoping Pole and Skimmer Net: To remove heavy leaves, twigs, and organic matter before pumping to prevent intake clogging.
- GFCI-Protected Extension Cord: A heavy-duty, outdoor-rated 12- or 14-gauge extension cord. Must be plugged exclusively into a Class-A Ground Fault Circuit Interrupter (GFCI) outlet for shock prevention.
- Pull Rope or Utility Cord: A 15- to 20-foot nylon cord tied to the pump's handle to position and retrieve the pump without stepping onto the unstable pool cover.
- Pump Stabilizing Plate: A wide plastic base plate or a flat kick-board to place under the pump, preventing the pump's suction intake from grabbing and tearing the vinyl cover fabric.
Expected Project Budget: $60 to $250 depending on pump specifications.Expected Project Duration: 1 to 4 hours, depending on water volume and pump GPH capacity.
Step-by-Step Water Removal Execution
Step 1: Clear All Organic Debris and Leaves
Before introducing any pumping equipment, you must clear the cover of floating leaves, twigs, and organic sludge. Attempting to pump water through a layer of leaves will instantly clog the pump’s intake screen, causing the motor to overheat and fail.
Using a telescoping pool pole equipped with a heavy-duty leaf rake or skimmer net, gently scoop the debris off the top of the water. Work systematically from the perimeter of the pool inward. Never use sharp tools, metal rakes, or tree branch trimmers near the cover, as these can easily puncture the synthetic material.
Step 2: Assemble and Prepare the Submersible Pump
Thread your garden hose or lay-flat discharge hose directly onto the pump's male discharge port. Ensure the rubber washer inside the hose female fitting is fully seated to prevent pressurized water leaks near the electrical housing.
If your pump is not equipped with a pre-installed base plate, place it securely on a flat, non-abrasive plastic plate. Tie your nylon pull rope securely to the pump's integrated molded handle. Do not tie the rope to the power cord or the discharge hose, as pulling these components will damage internal electrical seals and wire connections.
Step 3: Position the Pump in the Deepest Pool of Water
Standing safely on the solid pool deck, hold the nylon pull rope in one hand and the discharge hose in the other. Slowly lower the pump onto the pool cover. Use the rope to steer the pump toward the natural low point of the cover where the water is deepest.
Gently lower the pump until it rests flat on its stabilizing base. Do not drop or toss the pump onto the cover, as the impact can crack the plastic housing or damage the pool cover fabric underneath. Ensure the discharge hose is uncoiled, free of kinks, and positioned flat along the deck.
Step 4: Route the Discharge Hose and Power On
Run the discharge hose to a designated drainage zone that is physically lower than the pool deck. Ideal discharge zones include municipal storm drains, designated street gutters, or sloped areas of your yard away from the home’s foundation. Do not discharge the water onto dry clay soils or directly against retaining walls, as this can cause soil erosion or foundation shifting.
Plug the pump's power cord into your heavy-duty extension cord, then connect the extension cord to a GFCI-protected electrical outlet. If using a manual pump, look for immediate water output at the end of the discharge hose. If using an automatic pump, the internal float switch or electronic water sensor will activate the motor once it detects water levels exceeding 1.5 to 2 inches.
Step 5: Herd the Remaining Puddles
As the water level drops, the cover will rise, causing the remaining water to break up into isolated, shallow puddles away from the pump's intake. To capture this remaining water, use your telescoping pool brush to gently push the shallow puddles toward the pump.
Alternatively, you can carefully adjust the tension straps of a safety cover on one side of the pool, lowering that section slightly to create a temporary low point where the remaining water will naturally flow. Keep the pump running until the water level on the cover is less than 1/4 inch deep.
Warning: Never walk on a water-filled or frozen pool cover under any circumstances. Even safety covers anchored to concrete decks can fail under excessive weight, risking entrapment in the freezing water underneath. Always operate and position all tools from the safety of the pool deck.
Step 6: Power Down, Inspect, and Store
Once the water is removed, unplug the pump from the electrical source immediately to prevent the motor from running dry, which can ruin the internal water seals within minutes. Use the nylon pull rope to retrieve the pump from the center of the cover.
Inspect the cover for any signs of physical wear, such as fraying seams, loose anchors, or small pinholes. Disconnect the discharge hose, drain all remaining water from the pump casing to prevent internal freezing, and store the equipment in a dry, climate-controlled space.
Do Pool Covers Conserve Water in Brisbane, Australia
Technical Performance of Water Removal Methods
The table below outlines the primary methods for removing water from a pool cover, highlighting key technical parameters, flow rates, and ideal use cases to help you choose the best approach for your pool setup.
| Removal Method | Average Flow Rate (GPH) | Power Source Required | Best Suited For | Risk Level & Drawbacks |
|---|---|---|---|---|
| Automatic Submersible Pump | 1,200 – 1,800 GPH | 110V-120V AC (GFCI) | Large pools, heavy rainfall, automated winter maintenance | Low; auto-shutoff protects motor and cover structure |
| Manual Submersible Utility Pump | 500 – 1,000 GPH | 110V-120V AC (GFCI) | Controlled drainage, mid-sized pools | Medium; requires continuous monitoring to prevent dry running |
| Siphon Method (Gravity-Fed) | 150 – 300 GPH | None (Gravity/Hydrostatic) | Shallow accumulations, remote pools without power access | Low; slow flow rate, requires a natural downward yard slope |
| Wet/Dry Shop Vacuum | 600 – 900 GPH | 110V-120V AC (GFCI) | Clearing tiny residual puddles, leaf-choked corners | High; vacuum tank fills rapidly, requiring constant manual emptying |
| Manual Bucket Scooping | 50 – 100 GPH | Human Power | Emergency clearing of small spots | High; high risk of physical strain and accidental cover tearing |
Common Water Removal Failures and Field Remedies
The Pump Hum, but No Water Discharges
- Root Cause: The pump is experiencing an airlock. When a pump is lowered vertically into water, air can become trapped inside the impeller housing, preventing the pump from building the kinetic energy needed to push water up and out of the discharge hose.
- Actionable Fix: Unplug the pump from the power source. Submerge the pump into the water at a steep 45-degree angle to allow the trapped air bubbles to escape from the bottom intake grate. Once the bubbling stops, set the pump flat on its base, plug it back in, and ensure the discharge hose is lying completely flat without any elevated loops or sharp kinks.
The Pool Cover Keeps Sinking as Water is Pumped Off
- Root Cause: There is a hole or tear in the solid pool cover, or the water under the cover is displacing upward. When you pump water off a torn cover, you are actually pumping balanced pool water out from underneath the cover, creating a continuous vacuum that pulls the cover down further.
- Actionable Fix: Monitor the chemistry and level of your pool water. If the water level inside the pool is dropping at the exact same rate as the cover water, immediately turn off the pump. Locate the tear in the cover, patch it using an underwater vinyl repair patch kit, or wait until spring to drain the pool water safely from beneath the cover.
Rainwater Has Frozen Into a Solid Sheet of Ice
- Root Cause: Prolonged exposure to sub-freezing temperatures has solidified the standing water on the cover.
- Actionable Fix: Do not attempt to use a pump, shovel, or ice pick to clear frozen water. Sharp ice edges can easily slice through heavy vinyl and safety mesh, and the physical impact can break tension springs. Leave the ice undisturbed. The ice will naturally melt during the next thaw cycle, at which point you can safely deploy your submersible pump.
The Pump Clogs Instantly with Fine Silt and Algae
- Root Cause: Fine organic particles, pine needles, and decayed leaf matter are bypassing the outer cover screen and choking the impeller.
- Actionable Fix: Unplug the pump and pull it back to the deck. Remove the bottom plastic intake plate and clean out any trapped debris. Wrap the entire pump housing in a fine mesh laundry bag or a nylon window screen before lowering it back onto the cover. This acts as a highly effective pre-filter, stopping fine silt and pine needles from reaching the main intake.
Frequently Asked Questions
Can I use a regular household utility pump on my pool cover?
Yes, you can use a standard household utility pump as long as it is fully submersible and sits on a wide, flat base plate to prevent its suction port from grabbing and tearing the vinyl cover. It must always be connected to a GFCI-protected outlet to prevent the risk of severe electrical shock.
How often should I drain the water off my pool cover?
You should drain standing water off your pool cover whenever it accumulates to a depth of two inches or more, or immediately before a projected hard freeze. Keeping the cover clear of water prevents stress on the anchors and stops breeding grounds for mosquitos and algae in the spring.
Why does my pump stop pumping before the cover is completely dry?
Most submersible pumps require a minimum water depth of 1/2 inch to 1 inch to maintain prime and keep the impeller cool. Once the water falls below this threshold, the pump will lose suction and draw in air. Use a push broom to gather the remaining shallow puddles toward the pump to clear as much water as possible.
Can I use a garden hose to siphon water off a pool cover?
Yes, a garden hose can siphon water off a pool cover using gravity. Submerge the entire hose in the pool to fill it with water, cap one end with your hand, pull that end down to a lower point in your yard, and release it to start a continuous, gravity-fed siphon.
Will a mesh safety cover still collect water that needs to be pumped off?
Mesh safety covers are designed to allow water to drain through into the pool basin. However, if the mesh pores become clogged with fine debris, pine needles, or pollen, water can pool on top. You should gently brush the mesh surface with a pool brush to clear the clogged pores, allowing the water to drain through as intended.
Secure Your Investment with Professional Pool Care
Regularly clearing standing water from your pool cover is the single most effective way to prevent costly structural damage to your pool walls and extend the life of your winter cover. For premium winterization accessories, advanced automatic cover pumps, or expert assistance with opening your pool for the season, contact our professional pool care team today.