How To Get Rid Of Moss Between Pavers: A Professional Maintenance Guide

How To Get Rid Of Moss Between Pavers: A Professional Maintenance Guide

How to Get Rid of Moss on Pavers | Angi

Eradicating moss from paver joints requires a systematic approach combining mechanical removal, chemical neutralization of spores, and the restoration of structural joint stability. Achieving long-term results depends on adjusting the micro-environment—specifically reducing moisture retention and improving solar exposure—to ensure the pavers remain an inhospitable host for bryophyte colonization.


Essential Preparation and Technical Requirements

Removing moss is not merely an aesthetic task; it is a structural necessity. When moss roots penetrate the joint sand, they compromise the integrity of the base, causing pavers to shift and become uneven over time. Before beginning, evaluate the density of the growth and the drainage characteristics of your substrate.

Essential Gear and Material Checklist:



  • Mechanical Tools: A stiff-bristled wire brush, a long-handled garden hoe, or a pressure washer with a flat-surface attachment.
  • Application Tools: A pump sprayer, a stiff push broom, and a shop vacuum for precision debris removal.
  • Materials: Polymeric sand, household distilled white vinegar, oxygen bleach (sodium percarbonate), or commercial moss control agents.
  • Safety Equipment: Protective eyewear, chemical-resistant gloves, and rubber boots.
  • Benchmark Estimates: Plan for approximately 30 to 45 minutes of active labor per 100 square feet, depending on the severity of the infestation. Total costs range from $50 for basic cleaning agents to $200 for professional-grade polymeric sand and sealing products.

Professional Procedures for Moss Extraction

The following workflow prioritizes the physical removal of the organism followed by an acidic or alkaline treatment to prevent rapid re-colonization.



Step 1: Mechanical Debridement

Start by clearing the surface debris using a leaf blower or a standard stiff broom. If the moss is dry, use a wire-bristled brush to scrape the joints vigorously. For heavily impacted areas, utilize a pressure washer. Set the pressure washer to no more than 2,000 PSI to avoid damaging the concrete finish or eroding the bedding layer of sand beneath the pavers. Hold the nozzle at a 45-degree angle to the joint, moving steadily to lift the moss clusters without blowing out the entire base foundation.

Warning: Never use a zero-degree (pinpoint) pressure washer nozzle directly on the joints, as this will blast away the structural sand and destabilize the pavers, leading to rocking or sinking stones.



Step 2: Chemical Neutralization of Spores

Once the bulk moss is removed, the remaining microscopic spores must be neutralized. A solution of one part distilled white vinegar to two parts water is highly effective for smaller patches. For larger, persistent infestations, mix oxygen bleach with water according to the manufacturer’s instructions. Apply the solution liberally using a pump sprayer and allow it to dwell for 15 to 20 minutes. The acidity of the vinegar or the oxidation of the bleach will destroy the root systems embedded within the joints.

Pro-Tip: Perform this step on a bright, sunny day. Ultraviolet light, combined with the chemical application, significantly increases the kill rate of residual spores.



Step 3: Debris Evacuation and Joint Desiccation

After the dwell time, scrub the joints once more to loosen any remaining dead organic material. Use a shop vacuum to extract the slurry of dead moss and loosened sand. This step is critical; if you leave the organic matter in the gaps, it will act as a fertile compost for the next generation of spores. Allow the joints to dry completely for at least 24 to 48 hours.



Step 4: Installation of Polymeric Sand

The final step is the most important for prevention. Fill the cleaned, dry joints with polymeric sand. Sweep the sand across the pavers, ensuring it settles at least 1/8 inch below the chamfered edge of the stones. Use a vibrating plate compactor to ensure the sand settles deep into the joints. Lightly mist the surface with water to activate the polymers, which will harden the sand into a water-resistant, weed-suppressant barrier.


How to get rid of moss in lawns: 6 simple ways | Homes and Gardens

How to get rid of moss in lawns: 6 simple ways | Homes and Gardens

Comparative Analysis of Moss Removal Methods



Method Efficacy Environmental Impact Cost Efficiency Maintenance Interval
Mechanical (Wire Brush) Low None High Frequent
Vinegar/Acidic Rinse Moderate Low High Moderate
Oxygen Bleach High Low Moderate Long-term
Pressure Washing High Low Moderate Seasonal
Polymeric Sand Sealing Exceptional Low Moderate Permanent

Common Site Failures and Field Fixes



  • Root Cause: Persistent Regrowth in Shaded Areas. If the area is constantly shaded by heavy canopy, the moisture will never evaporate sufficiently.

    • Actionable Fix: Trim overhanging tree branches to increase sunlight exposure. If trimming is not possible, consider installing a professional-grade drainage system to divert runoff away from the pavers.
  • Root Cause: Sand Washout. If the joints are empty, they will fill with soil and organic dust, providing a substrate for new moss.

    • Actionable Fix: Ensure that you have used the correct grade of polymeric sand and that the activation process was thorough. Apply a secondary layer if gaps appear after the first rainfall.
  • Root Cause: Acidic Soil Runoff. If the pavers are located near landscape beds with pine needles or acidic soil, the pH level of the surface will naturally favor moss.

    • Actionable Fix: Apply a lime-based paver sealer that shifts the surface pH to a more alkaline state, making it hostile to moss colonization.

Frequently Asked Questions



Does salt work to kill moss between pavers?

While salt is an effective herbicide, it is not recommended for use on pavers. Salt can cause efflorescence, a white powdery staining on the surface of the stones, and it may damage the concrete structure or surrounding vegetation.



How often should I re-apply polymeric sand to keep moss away?

In ideal conditions, a properly installed layer of polymeric sand can last between three to five years. Inspect your joints annually after the winter thaw to identify any cracking or washout that could allow moisture and spores to re-enter.



Can I just use a regular weed killer for moss?

Standard lawn weed killers are typically formulated for vascular plants and are largely ineffective against bryophytes like moss. You must use a product specifically labeled for moss or algae control, such as those containing ferrous sulfate or sodium percarbonate.



Why does my driveway get moss even when it is not in the shade?

Moss thrives on humidity and standing water as much as shade. If your pavers are improperly sloped, water will pool rather than drain, creating a damp environment that allows moss to flourish regardless of sunlight exposure.

Protect Your Investment with Professional Care

Maintaining clear joints is the primary defense against long-term paver degradation and costly structural repairs. Implement these maintenance steps today to ensure your hardscape remains clean, stable, and visually pristine for years to come.


How To Get Rid Of Moss Between Paver Bricks at Richard Buffum blog

How To Get Rid Of Moss Between Paver Bricks at Richard Buffum blog

Read also: Azalea Plaza shopping center renovations will bring five new stores