How To Get Air Out Of Power Steering: A Complete Bleeding Guide
Bleeding air out of a power steering system requires replacing trapped gas pockets with hydraulic fluid by cycling the steering wheel lock-to-lock with the engine off and on. Neglecting this procedure leads to premature pump cavitation, fluid aeration, and permanent steering gear damage.
Pre-Procedure Planning and Technical Setup
Hydraulic steering systems rely on an incompressible fluid medium to transmit force from the rotary control valve to the steering rack or steering box. When air enters this closed-loop circuit—typically during pump replacement, hose disconnection, or low fluid operation—it compresses rather than flows, causing erratic steering resistance, whining noises, and a spongy pedal or wheel feel.
Essential Gear, Tools, and Materials:
- Manufacturer-specified power steering fluid (e.g., ATF Type DEXRON III/VI, Honda/Acura specific fluid, or CHF 11S/202 synthetic hydraulic oil)
- Floor jack and secure jack stands
- Turkey baster or fluid suction syringe
- Clean shop rags and funnel
- Wheel chocks
Prerequisite Knowledge and Standards:
- Verify the vehicle's service manual for specific fluid requirements; mixing mineral-based and synthetic fluids destroys internal seals.
- Ensure the vehicle's front wheels are safely elevated off the ground to minimize high-load friction against the pavement while cycling dry or semi-dry steering components.
Estimated Time and Budget:
- Time required: 30 to 45 minutes.
- Budget: 10 to 20 dollars for fluid.
Step-by-Step Power Steering Bleeding Procedure
Step 1: Elevate and Secure the Vehicle
Position wheel chocks behind the rear tires to prevent any rolling movement. Engage the emergency parking brake firmly. Position a hydraulic floor jack beneath the manufacturer-designated front subframe jacking point and lift the front end until both front tires clear the ground by at least two inches. Lower the vehicle securely onto certified jack stands to ensure a stable workspace while accessing the steering linkage.
Step 2: Inspect and Evacuate the Reservoir
Locate the power steering fluid reservoir under the hood and clean any dirt or debris from the surrounding cap to prevent contamination. Remove the cap and inspect the existing fluid condition. If the fluid appears foamy, pinkish, milky, or dark brown with suspended micro-bubbles, use a turkey baster or fluid suction pump to extract the contaminated fluid from the reservoir down to the inlet port.
Step 3: Fill with Fresh Hydraulic Fluid
Pour fresh, manufacturer-approved power steering fluid directly into the reservoir until the fluid level reaches the Cold Full mark. Leave the reservoir cap off during the initial mechanical cycling phases to allow trapped air bubbles to vent freely to the atmosphere as they rise through the return line.
Warning: Never use automatic transmission fluid (ATF) in systems specifically engineered for European mineral-based hydraulic oils such as Pentosin CHF, as incompatible chemical compositions will swell and destroy high-pressure rubber seals instantly.
Step 4: Perform Cold Static Steering Cycles
With the engine completely switched off, slowly rotate the steering wheel from absolute full left lock to absolute full right lock. Pause for two to three seconds at each extreme lock position to let fluid pressure displace trapped air pockets within the rack assembly. Repeat this lock-to-lock sweeping motion continuously between 15 and 20 times. Monitor the fluid reservoir level constantly, topping it off before it drops low enough to pull fresh air back down into the pump feed line.
Step 5: Check for Aeration and Settle the System
Observe the fluid inside the reservoir while performing the static cycles. You will likely see tiny bubbles rising to the surface and micro-foaming occurring as the air escapes. Once the fluid stops showing active foam generation during lock-to-lock rotations, allow the system to rest undisturbed for 10 minutes so suspended microscopic air bubbles can naturally aggregate and float upward.
Step 6: Purge Under Operating Pressure
Start the engine and let it idle smoothly. Do not touch the steering wheel immediately; allow the positive displacement pump to circulate fluid through the low-pressure return circuit for 60 seconds at standard idle speed. While the engine runs, slowly cycle the steering wheel from lock to lock an additional five times. Watch the reservoir fluid level closely, as the pump will pull fluid down rapidly once internal control valves actuate. Turn off the engine immediately if the pump begins producing a loud, high-pitched groaning sound, which indicates low fluid starvation and active cavitation.
Air Out, Power In - Efficiency with Brake Fluid Tronic — Your Source ...
Power Steering Fluid Specifications and System Types
| System Classification | Primary Fluid Standard | Bleeding Sensitivity | Operating Pressure Range |
|---|---|---|---|
| Conventional Hydraulic Rack & Pinion | ATF (DEXRON III / Mercon) | Moderate | 1,200 – 1,500 PSI |
| European Closed-Loop Hydraulic | CHF 11S / CHF 202 Synthetic | High (Strictly synthetic only) | 1,500 – 1,800 PSI |
| Asian Hydraulic Systems | PSF-II / Spec-Specific Fluid | Low to Moderate | 1,100 – 1,400 PSI |
| Electro-Hydraulic Power Assisted (EHPS) | Varies (ATF or CHF) | Critical (Requires electronic reset) | 1,500 – 2,000 PSI |
Common Bleeding Complications and Field Fixes
Persistent Foaming and Whining Noise:
- Root Cause: A micro-leak on the suction side (low-pressure inlet hose between the reservoir and the pump inlet) is allowing ambient air to be drawn into the system under vacuum.
- Actionable Fix: Inspect, tighten, or replace the constant-tension spring clamp or worm-gear clamp on the pump inlet hose. Replace the inlet hose if rubber degradation is visible.
Stiff Steering Zones or Binding:
- Root Cause: Large air pockets trapped deep within the steering rack spool valve or internal rotary actuator channels that resist standard static cycling.
- Actionable Fix: Repeat the static lock-to-lock cycle process with the front end elevated, but apply moderate manual force against the stops at each end to help shift stubborn air pockets past tight valve clearances.
Fluid Overflow During Bleeding:
- Root Cause: Rapid expansion of aerated fluid or overfilling the reservoir past the hot/cold indicators prior to completing the air purge cycles.
- Actionable Fix: Use a turkey baster to lower the fluid level to the minimum cold line, install the cap loosely, and complete additional low-speed cycling before re-checking levels.
Frequently Asked Questions
Can I use regular engine oil if I run out of power steering fluid?
Never use engine oil, brake fluid, or gear oil in a power steering system. These fluids possess vastly different viscosity indexes and chemical additives that will degrade internal seals, clog precision valve orifices, and cause complete hydraulic pump failure.
Why does my power steering whine only when it is cold outside?
Cold temperatures cause rubber hoses to contract and power steering fluid to thicken, which restricts flow into the pump inlet port. This flow restriction creates a localized vacuum that pulls air past micro-cracks or loose hose clamps, resulting in pump cavitation and whining until the fluid warms up.
Do I need to lift the wheels off the ground to bleed the system?
Lifting the front wheels off the ground is strongly recommended because it dramatically reduces the mechanical load and friction between the tires and the ground. This makes turning the wheel smooth and prevents premature wear on steering components while the system is dry or partially filled with air.
How long does it take for micro-bubbles to naturally disappear from the fluid?
Trapped micro-bubbles typically require 10 to 15 minutes of undisturbed rest inside the reservoir to aggregate and rise to the surface. Forcing the pump to run continuously with aerated fluid will only whip the air back into a persistent foam.
Ensure optimal hydraulic performance and extend the operational lifespan of your steering components by using manufacturer-certified fluids and strictly following pressure-purge protocols.