Mastering The Cut: The Professional Guide To Cutting Railroad Ties For Landscaping

Mastering The Cut: The Professional Guide To Cutting Railroad Ties For Landscaping

How To Install Railroad Tie Steps at Eden Disney blog

Cutting railroad ties effectively requires a high-torque chainsaw equipped with a carbide-tipped chain to penetrate dense, creosote-treated hardwood while resisting the abrasive grit embedded in the grain. Success depends on maintaining consistent engine RPMs and utilizing a four-sided marking technique to ensure a perfectly square 7-by-9-inch cross-section, all while adhering to strict environmental and respiratory safety protocols.


Pre-Operation Requirements and Equipment Specifications

Before engaging in the physical act of cutting, one must understand the unique composition of a railroad tie. Most domestic ties are constructed from dense hardwoods such as oak, hickory, or beech, though some western variants utilize Douglas fir. These timbers are pressure-treated with coal-tar creosote, a thick, oily preservative that acts as a pesticide and fungicide. This chemical treatment, combined with decades of exposure to track ballast (crushed stone) and metallic microscopic dust from passing trains, makes railroad ties one of the most abrasive materials a woodworker or landscaper will ever encounter.

Standard carbon steel chainsaw chains are designed for green or seasoned logs; however, when applied to a used railroad tie, the embedded silica and metal shavings will dull a standard edge in as little as two or three cuts. Therefore, the selection of high-performance equipment is not merely a preference but a mechanical necessity.



Essential Equipment and Safety Checklist



  • High-Torque Chainsaw: A gasoline-powered saw with at least 50cc displacement or a high-voltage (60V+) cordless professional model is required. Small homeowner-grade saws often overheat due to the density of the treated wood.
  • Carbide-Tipped Chain: Standard steel chains fail almost immediately. A carbide-tipped chain retains its edge significantly longer when encountering the grit and stones embedded in the tie’s exterior.
  • Respiratory Protection: An N95 or P100 respirator is mandatory. Creosote-soaked sawdust is a known carcinogen and a severe respiratory irritant.
  • Personal Protective Equipment (PPE): Chainsaw chaps (Class 1 or 2), impact-resistant eye protection, heavy-duty work gloves, and steel-toed boots.
  • Measurement and Marking Tools: A speed square, a bright-colored lumber crayon or chalk line, and a heavy-duty tape measure.
  • Supports: Heavy-duty sawhorses or sacrificial 4x4 timber blocks to elevate the tie off the ground, preventing the chain from striking the soil.

Systematic Execution of the Railroad Tie Cut

Cutting a railroad tie is a process that balances brute force with precision. Because a standard tie measures approximately 7 inches by 9 inches, a standard 16-inch or 18-inch chainsaw bar is ideal. The goal is to achieve a square face that allows for tight stacking in retaining walls or garden borders.



Step 1: Inspection and Decontamination

Before placing the tie on your cutting stand, perform a visual and physical inspection of the entire length of the timber. Used ties are notorious for containing "hidden" hazards. Use a wire brush to scrub the area where the cut will be made. Look specifically for broken-off rail spikes, "S-irons" (metal plates driven into the ends to prevent splitting), and deeply embedded gravel.

Warning: Striking a steel rail spike with a chainsaw at full throttle can cause immediate chain breakage or a violent kickback, leading to severe injury. If you detect metal that cannot be removed, shift your cut line at least three inches away from the obstruction.



Step 2: Precision Marking for a Square Finish

One of the most common failures in landscaping projects is "wandering" cuts that result in slanted ends. To prevent this, mark the tie on all four sides.



  1. Use your tape measure to determine the length.
  2. Use a speed square and a lumber crayon to draw a line across the top face.
  3. Extend that line down both vertical sides.
  4. Flip the tie and connect the lines on the bottom face. This 360-degree guide ensures that even if your bar begins to drift, you have a visual reference point on every side to correct your trajectory.


Step 3: Elevation and Stabilization

Never cut a railroad tie while it is sitting directly on the ground. Not only does this risk "bucking" the saw if the blade hits a rock, but the dirt itself will instantly ruin your chain’s sharpening. Elevate the tie onto two sacrificial pieces of wood or heavy-duty sawhorses. Position the supports so that the section being cut off will fall away freely. This prevents the "kerf" (the gap created by the blade) from closing and pinching the chainsaw bar, which can trap the saw and cause the engine to stall or the chain to jump.



Step 4: The Primary Cutting Procedure

Start your chainsaw and allow it to reach full operating temperature.



  1. Align the bar with the top marking line.
  2. Engage the throttle fully before the chain touches the wood.
  3. Apply steady downward pressure, but let the weight of the saw do the work.
  4. If you are using a standard chain (not recommended), you may need to use a "rocking" motion—lifting the back handle slightly and then the front—to clear sawdust from the cut.
  5. With a carbide chain, maintain a flat, level plane.

Pro-Tip: If the saw begins to produce fine dust rather than distinct wood chips, your chain is dull. Stop immediately and sharpen or replace it. Forcing a dull chain through creosote-treated hardwood generates extreme friction heat, which can warp your guide bar and destroy the saw’s internal seals.



Step 5: Handling the Breakthrough

As you reach the final inch of the cut, reduce downward pressure. This prevents the weight of the falling "drop" piece from splintering the bottom of the tie. Once the piece falls, release the throttle and wait for the chain to stop completely before removing the saw from the work area.



Step 6: Post-Cut Cleanup and Disposal

The sawdust generated from cutting railroad ties is toxic. Use a broom and dustpan to collect as much sawdust as possible. Do not leave it on the soil, as the concentrated creosote can leach into the ground and kill surrounding vegetation. Dispose of the sawdust and any small off-cuts in accordance with local municipal hazardous waste regulations.


How to Remove Railroad Ties

How to Remove Railroad Ties

Technical Comparison of Cutting Methodologies

The following table compares the three most common methods for cutting railroad ties, highlighting why specific tools are preferred for different scales of work.



Feature Chainsaw (Carbide Chain) Reciprocating Saw (Diablo/Carbide) Circular Saw (7-1/4")
Primary Use Bulk cutting and thick cross-sections. Precision trimming or small repairs. Initial scoring or shallow cuts.
Cutting Speed Very High (30-60 seconds per cut). Low (5-10 minutes per cut). Moderate (Requires 2-3 passes).
Depth Capacity Up to 18" or more. 9" to 12" (with long blades). 2.5" max (cannot cut through).
Chain/Blade Wear High (Requires carbide tips). Extremely High (Blades dull fast). High (Tends to gum up with oil).
User Fatigue Moderate (Weight of saw). High (Extreme vibration). Low (Standard operation).
Accuracy Moderate (Requires steady hand). Low (Blade flexes easily). High (Limited by depth).

Troubleshooting Common Cutting Failures

Navigating the difficulties of treated timber requires an understanding of both mechanical and environmental variables. Below are common failures encountered in the field and their professional remedies.



  • Problem: The chainsaw bar is smoking and the wood is charring.



    • Root Cause: This is typically caused by a dull chain or insufficient bar oil. Creosote is a sticky substance that can clog the oiler hole on your chainsaw bar, preventing lubrication.
    • Actionable Fix: Stop the saw and clear the oiler port with a small wire. Check the chain tension; a chain that is too tight creates excess friction. If the chain is sharp and oiled, slow down your feed rate.
  • Problem: The cut is consistently curving to one side.



    • Root Cause: This usually indicates that the cutters on one side of the chain are sharper than the other, or the guide bar rails have worn unevenly.
    • Actionable Fix: Flip the guide bar over to ensure even wear on the rails. If the problem persists, the chain must be professionally sharpened on a mechanical grinder to ensure all teeth are at the exact same angle and length.
  • Problem: The engine stalls as soon as the blade enters the wood.



    • Root Cause: This is often "pinching" caused by improper support. If the tie is sagging in the middle, the kerf will close on the bar as you cut.
    • Actionable Fix: Re-position your supports so that the tie is supported on both sides of the cut, but ensure the "waste" side is slightly cantilevered so the cut opens up as you progress.

Frequently Asked Questions



Is it safe to use a circular saw to cut railroad ties?

A standard circular saw cannot cut through the 7-inch thickness of a railroad tie in a single pass. While you can score the edges or make a 2.5-inch deep cut on all four sides, you will still need to finish the center with a hand saw or reciprocating saw. Furthermore, the oily creosote often gums up circular saw blades, leading to dangerous kickbacks.



How many cuts can I expect from a single carbide chain?

Depending on the age of the tie and the amount of embedded grit, a high-quality carbide-tipped chain can typically handle 20 to 40 cuts before requiring professional sharpening. In contrast, a standard steel chain may become useless after just 2 or 3 cuts in the same material.



Can I burn the scraps or sawdust from railroad ties?

No. Burning railroad ties is illegal in many jurisdictions and extremely hazardous to your health. Combustion releases the creosote and other chemical preservatives into the air as toxic smoke and concentrates the toxins in the ash. Always dispose of scraps at a designated landfill.



Why do railroad ties smell so strongly when being cut?

The friction of the blade heats the coal-tar creosote, causing it to "off-gas." This creates the distinct, pungent odor of mothballs or hot asphalt. This is why wearing a respirator and working in a well-ventilated outdoor area is critical to prevent chemical inhalation.

Professional Landscaping Support

Achieving a professional-grade finish on your landscaping project requires the right tools and a commitment to safety. If your project involves a high volume of timber work, consider investing in professional-grade carbide equipment to ensure every cut is as precise as the first.


Railroad Ties In Playgrounds - Alpharetta GA Landscape Timbers ...

Railroad Ties In Playgrounds - Alpharetta GA Landscape Timbers ...

Read also: How to Beat a DWI: Strategic Legal Defense and Procedural Analysis