How To Convert A Natural Gas Furnace To Propane: A Step-by-Step Technical Guide

How To Convert A Natural Gas Furnace To Propane: A Step-by-Step Technical Guide

Propane Conversion Natural Gas Propane Conversion Chart

Converting a natural gas furnace to liquid propane (LP) requires downsizing the burner orifices and recalibrating the gas valve regulator to handle propane's higher energy density and delivery pressure. By replacing the stock orifices and adjusting manifold pressure from the standard 3.5 inches Water Column (" WC) to 10.0–11.0" WC using an OEM-certified conversion kit, you ensure safe ignition, complete combustion, and code compliance.


Technical Prerequisites and Safety Equipment Checklist

Converting a residential or commercial gas furnace from natural gas to liquid propane is a precision technical task regulated by NFPA 54 (National Fuel Gas Code) and ANSI Z223.1 standards. Propane contains approximately 2,520 BTUs per cubic foot—more than double the energy density of natural gas (1,030 BTUs per cubic foot). Furthermore, propane operates at significantly higher manifold pressures. Executing this conversion without exact matching components will cause catastrophic overfiring, severe soot accumulation, high carbon monoxide generation, or heat exchanger failure.



Essential Tools and Conversion Equipment



  • OEM Propane Conversion Kit: Manufacturer-specified kit containing LP orifices, regulator spring/conversion cap, low-pressure switch (if required), and code-mandated warning labels.
  • Digital Manometer or U-Tube Manometer: Dual-port capable, measured in inches Water Column (" WC) with a minimum resolution of 0.01" WC.
  • Orifice Socket / Nut Driver: Deep-well 1/4-inch, 5/16-inch, or 1/2-inch socket (model-dependent).
  • Combustion Analyzer: Portable unit capable of measuring O2, CO, CO2, draft pressure, and flue temperature.
  • Non-Corrosive Gas Leak Detection Fluid: Electronic combustible gas leak detector or approved bubble solution.
  • Hand Tools: Calibrated torque wrench, adjustable wrenches, hand screwdrivers, Teflon tape rated for gas lines (yellow gas tape).


Prerequisites and Industry Compliance



  • Unit Compatibility Verification: Check the furnace data plate to confirm the unit is field-convertible. Look for explicit designation tags such as "Design Certified for Natural Gas and LP."
  • Inlet Pressure Verification: Liquid propane must be delivered to the gas valve at an inlet pressure between 11.0" WC and 13.0" WC (0.4 to 0.47 PSI). A dedicated two-stage propane regulator system must be installed at the supply tank.
  • Time & Budget Benchmarks: DIY/Professional conversion time ranges from 1.5 to 3 hours. OEM conversion kit costs typically range between $40 and $120, excluding specialized calibration instrumentation.

Comprehensive Step-by-Step Furnace Conversion Protocol



Step 1: System De-Energization and Gas Supply Isolation



  1. Turn off the electrical power supply to the furnace at the primary circuit breaker panel or the local service disconnect switch adjacent to the unit.
  2. Rotate the external gas shutoff valve on the hard pipe supply line 90 degrees to the "OFF" position (perpendicular to the pipe run).
  3. Turn the gas valve control knob inside the furnace burner compartment from "ON" to "OFF".
  4. Allow the heat exchanger and burner assembly to cool completely for at least 20 minutes before touching any internal mechanical assemblies.

Warning: Never attempt to convert a furnace while the main power is energized or the gas supply is pressurized. Residual gas in the manifold can ignite, and shorting low-voltage control circuits can destroy the integrated furnace control board.



Step 2: Burner Compartment Access and Manifold Disassembly



  1. Remove the upper access door of the furnace cabinet to expose the burner compartment, igniter, flame sensor, and gas manifold assembly.
  2. Carefully disconnect the wiring harness leading to the main gas valve solenoid. Label the wires if they are not keyed.
  3. Disconnect the hot surface igniter (HSI) lead plug. The silicon carbide or silicon nitride element is extremely brittle; do not strike or handle the element directly with bare fingers.
  4. Remove the screws securing the gas manifold pipe to the burner mounting brackets using a nut driver.
  5. Unthread the union fitting or flexible gas connector joining the incoming fuel supply line to the gas valve inlet port.
  6. Slide the entire gas valve and manifold assembly forward, pulling the orifices out of the burner venturi throats, and set the assembly on a clean work surface.


Step 3: Gas Orifice Extraction and Replacement



  1. Identify the brass natural gas orifices threaded into the manifold assembly. Natural gas orifices feature significantly larger physical apertures (typically #42 to #45 Drill Measurement Size) than propane orifices (typically #54 to #56 Drill Measurement Size).
  2. Using a deep-well socket, unthread each natural gas orifice counterclockwise from the manifold manifold rail. Take care not to cross-thread or deform the aluminum/steel manifold threads.
  3. Inspect the replacement LP orifices supplied in the OEM conversion kit. Verify that the stamped drill size matching the high-altitude or standard rating matches your furnace's BTU rating table in the installation manual.
  4. Thread the new LP orifices clockwise into the manifold by hand to ensure proper thread alignment.
  5. Tighten each LP orifice using the socket wrench to approximately 35–45 in-lbs of torque. Do not overtighten, as brass threads strip easily under excessive torque.

Pro-Tip: Always double-check orifice numbers under bright light. Installing a natural gas orifice on a liquid propane supply line will dump more than twice the required fuel volume into the combustion chamber, resulting in violent ignition spikes, heavy soot deposits, and lethal carbon monoxide output.



Step 4: Gas Valve Regulator Spring and Cap Conversion



  1. Locate the pressure regulator cover screw on the main gas valve (commonly White-Rodgers, Honeywell, or SIT valves).
  2. Remove the plastic or metal slot-headed cover screw to expose the internal regulator adjustment mechanism.
  3. For spring-replacement style valves: Unthread the plastic adjustment screw, extract the long silver Natural Gas regulator spring, insert the shorter/stiffer red or black LP regulator spring from the kit, and rethread the adjustment screw.
  4. For convertible cap style valves: Unscrew the cap, flip the internal plunger stem 180 degrees so the "LP" designation faces outward/downward according to manufacturer specs, and screw the cap back in.
  5. Reinstall the cover screw finger-tight until final manometer pressure calibration is performed.


Step 5: Manifold Reassembly and Static Leak Testing



  1. Re-align the manifold assembly so each new LP orifice centers precisely inside the entrance of its corresponding burner tube.
  2. Secure the manifold assembly to the burner support brackets using the factory mounting screws.
  3. Reconnect the hot surface igniter wiring harness and the gas valve electrical leads.
  4. Apply yellow PTFE gas pipe sealant to the threaded joints of the gas line and reconnect the main gas pipe union.
  5. Turn the external gas shutoff valve to the "ON" position to pressurize the line up to the gas valve.
  6. Apply non-corrosive leak detection fluid across all newly assembled threaded joints, the gas valve inlet, and the pressure test ports. Observe for 3 minutes. If expanding bubbles appear, immediately turn off the gas, disassemble the connection, reapply sealant, and retighten.


Step 6: Dynamic Pressure Calibration and Manometer Tuning



  1. Turn off the gas valve and remove the 1/8-inch NPT outlet pressure tap plug on the gas valve body.
  2. Thread a barb fitting into the outlet pressure port and attach the high-pressure hose of your digital manometer.
  3. Turn the main gas supply back on and switch the furnace control knob to "ON".
  4. Restore electrical power to the furnace and set the wall thermostat to call for heat.
  5. Allow the inducer draft motor to run, the igniter to warm up, and the main burners to ignite.
  6. Read the dynamic manifold pressure on the digital manometer once ignition stabilizes.
  7. Adjust the gas valve regulator adjustment screw until the manometer reads the precise specification listed on the LP conversion decal (typically 10.0" WC to 10.5" WC for single-stage, or 10.5" WC on High Fire / 4.9" WC on Low Fire for two-stage units). Turn clockwise to increase pressure; counterclockwise to decrease pressure.
  8. Shut down the furnace call for heat, remove the manometer, and replace the NPT outlet port plug with pipe thread sealant applied.


Step 7: Flue Gas Analysis and System Labeling



  1. Re-energize the furnace and initiate a full heating cycle.
  2. Insert the probe of a calibrated combustion analyzer into the vent pipe flue sampling port (12–24 inches downstream of the draft inducer outlet).
  3. Measure the combustion parameters: Carbon Monoxide (CO) must read below 100 PPM air-free (ideally under 50 PPM), and Oxygen (O2) should typically range between 4.0% and 7.0%.
  4. Affix the mandatory conversion decal included in the kit directly beside the original furnace rating plate.
  5. Fill out the technician details on the label, including date, conversion kit part number, operating pressure, orifice size, and installer credentials.

Miller Propane Furnace | Gas Furnace

Miller Propane Furnace | Gas Furnace

Technical Fuel Metrics and Operational Thresholds

The operational parameters between Natural Gas and Liquid Propane differ significantly. The following standard values must be maintained during furnace operation:



Parameter / Specification Natural Gas (NG) Standard Liquid Propane (LP) Standard Technical Significance
Gross Heating Value ~1,030 BTU/ft³ ~2,520 BTU/ft³ LP delivers ~2.45x heat energy per volume unit.
Specific Gravity (Air = 1.0) 0.60 to 0.65 (Lighter than air) 1.50 to 1.55 (Heavier than air) Leaking LP pools in basements/floors; NG rises.
Recommended Inlet Gas Pressure 5.0" WC to 7.0" WC 11.0" WC to 13.0" WC Requires two-stage regulator setup at LP tank.
Target Manifold Pressure (Single Stage) 3.5" WC (± 0.3" WC) 10.0" WC to 10.5" WC (± 0.3" WC) Proper pressure ensures complete fuel atomization.
Typical Orifice Drill Size (Sea Level) #42 to #45 DMS #54 to #56 DMS LP requires much smaller cross-sectional hole area.
Flame Speed / Characteristics Moderate speed; Soft blue flame Rapid speed; Hard blue inner cone LP requires precise air shutter / draft setup.
Max Allowable Flue CO (Air-Free) < 400 PPM (Target < 100 PPM) < 400 PPM (Target < 50 PPM) High CO indicates incomplete LP combustion.

Diagnostic Protocols for Post-Conversion Failures



Scenario 1: Heavy Soot Accumulation and Yellow Flame Patterns



  • Root Cause: Excessive fuel delivery or severe lack of primary combustion air. This occurs when natural gas orifices were left in place, an incorrect LP orifice size was installed, or the manifold pressure exceeds 11.0" WC.
  • Actionable Fix: Immediately shut down the system. Inspect and replace the orifices with the precise DMS size specified in the LP conversion manual for your altitude. Connect a manometer to the gas valve outlet port and dial back the regulator spring adjustment to 10.0"–10.5" WC. Clean soot from the heat exchanger and burners using a wire brush and vacuum before restarting.


Scenario 2: Main Burners Fail to Ignite or Experience Violent "Delayed Ignition"



  • Root Cause: Manifold gas pressure is too low (< 8.0" WC), orifice ports are clogged with thread sealant, or the low-pressure cutout switch (if equipped) is open due to insufficient tank supply pressure.
  • Actionable Fix: Check the LP tank level to ensure it is above 20%. Measure inlet gas pressure at the valve—if below 11.0" WC under load, adjust or replace the second-stage LP regulator at the building line. Remove the manifold, inspect the orifices under light, clear obstructions with compressed air (do not ream with metal tools), and reset manifold pressure to 10.5" WC.


Scenario 3: Furnace Short-Cycles on High-Temperature Limit Switch



  • Root Cause: Thermal overfiring caused by elevated manifold pressure or improper high-altitude orifice selection. Overfiring forces the heat exchanger past its thermal envelope, tripping the primary limit switch.
  • Actionable Fix: Calculate the actual firing rate by timing the gas meter or taking dynamic flow measurements. Derate the orifice size by 4% per 1,000 feet above sea level (refer to OEM high-altitude charts). Turn the gas valve adjustment screw counterclockwise to lower manifold pressure to the lower threshold specified on the furnace rating plate.


Scenario 4: Gas Valve Fails to Open / Low-Pressure Switch Lockout



  • Root Cause: Modern high-efficiency furnaces operating on LP often require a dedicated Low Pressure Switch wired in series with the gas valve. If supply pressure drops below 9.0" WC, the safety switch opens, preventing valve energization.
  • Actionable Fix: Verify that the inline low-pressure switch supplied in the conversion kit is correctly wired to the control board gas valve circuit. Test continuity across the switch contacts using a multimeter. If open, trace the incoming supply line to identify restrictions, closed valves, or an improperly adjusted LP tank regulator.

Frequently Asked Questions



Can I convert any natural gas furnace to propane without a kit?

No, you cannot safely convert a furnace without an OEM-certified conversion kit. Natural gas components allow far too much fuel to pass through when connected to liquid propane, creating severe explosion, fire, and carbon monoxide hazards. Always use the manufacturer-specified kit matching your exact furnace model number.



How do I know what size propane orifices my furnace requires?

Orifice sizing depends on the furnace’s total BTU input rating, the number of burners, and the elevation above sea level where the unit is installed. The installation manual included with the OEM propane conversion kit provides a matrix that correlates drill measurement sizes (e.g., #54 DMS vs #56 DMS) to these specific variables.



What happens if I forget to change the gas valve regulator spring?

If you replace the orifices but fail to convert the gas valve regulator spring, the gas valve will only deliver approximately 3.5" WC of manifold pressure instead of the required 10.0"–11.0" WC. This results in severe underfiring, delayed ignition, burner flutter, poor heating performance, and potential lockout conditions on the control board.



Why does liquid propane require smaller burner orifices than natural gas?

Liquid propane contains more than twice the heat content per cubic foot compared to natural gas and operates under roughly three times the manifold pressure. Smaller orifices restrict the volume of propane entering the burners so the resulting air-fuel mixture remains balanced and within safe combustion parameters.

Professional HVAC Inspection and Conversion Support

Executing a furnace fuel conversion requires absolute precision, strict adherence to mechanical codes, and specialized diagnostic instruments. If you lack a digital manometer, combustion analyzer, or certified training, contact a licensed HVAC professional to complete the final calibration and safety inspection.


How To Convert From Natural Gas To Propane Furnace at Carmen More blog

How To Convert From Natural Gas To Propane Furnace at Carmen More blog

Read also: Gym members are arguing over the planet fitness $99 promo code