How To Clean Remington 870: Complete Step-by-Step Maintenance Guide

How To Clean Remington 870: Complete Step-by-Step Maintenance Guide

Remington 870 Express, Hardwood Home Defense | Boresight Solutions

Proper maintenance of a Remington 870 pump-action shotgun prevents carbon build-up and mechanical jams by stripping the firearm, scrubbing the chamber and bore, and applying a protective micro-film of gun oil to all carbon steel components. Regular field stripping and cleaning preserve the legendary reliability of this iconic 12-gauge platform while preventing premature wear on the action bars and trigger assembly.


Pre-Operation & Equipment Checklist

Maintaining a Remington 870 requires specific tools designed to protect the blued or parkerized finish while aggressively removing powder residue, lead fouling, and plastic wad shavings. Establish a clean, well-lit workbench covered with a silicone or oil-resistant mat before beginning the breakdown process.



  • Essential Gear and Consumables:

    • Solid brass cleaning rod with a rotating handle (avoid aluminum rods to prevent barrel scoring).
    • Caliber-specific bronze bore brush (12-gauge or 20-gauge depending on your model) and a cotton jag.
    • High-grade gun solvent (such as Hoppe's No. 9 or standard CLP).
    • Synthetic gun oil or high-temperature grease for slide rails.
    • Lint-free microfiber cleaning patches and heavy-duty shop rags.
    • Nylon-bristled utility brush (toothbrush style) and wooden toothpicks for hard-to-reach crevices.
  • Mandatory Prerequisites and Safety Standards:

    • Verify the firearm is completely unloaded by visually and physically inspecting both the chamber and the magazine tube.
    • Work in a well-ventilated area away from open flames when using aerosol solvents or cleaners.
    • Keep ammunition completely separated from the cleaning workspace to prevent accidental loading incidents.
  • Operational Benchmarks:

    • Estimated duration: 30 to 45 minutes for a standard field strip and deep clean.
    • Recommended frequency: Every 250 to 500 rounds, or immediately after exposure to moisture, saltwater spray, or heavy dust environments.

Step-by-Step Remington 870 Maintenance Workflow



Step 1: Safety Verification and Unloading

Confirm the safety status of the Remington 870 by pointing the muzzle in a safe direction and pulling the slide to the rear. Look directly into the ejection port and feel inside the chamber with your index finger to ensure zero live shells remain. Depress the shell elevator inside the loading port and push the follower forward to confirm the magazine tube is entirely empty.

Warning: Never rely solely on visual inspection; always perform a physical finger check of the chamber and tubular magazine to guarantee zero live ammunition is present in the firearm.



Step 2: Barrel and Magazine Cap Removal

Unscrew the magazine cap located at the very front of the firearm by turning it counter-clockwise until it completely disengages from the magazine extension tube. Pull the barrel straight forward and away from the receiver, ensuring the barrel locking ring clears the magazine tube. Set the barrel aside on your cleaning mat.

Pro-Tip: If the magazine cap is excessively tight from factory torque or accumulated grit, wrap a rubber strap wrench around the cap to gain leverage without scratching the bluing.



Step 3: Trigger Assembly and Bolt Extraction

Push out the trigger plate pin located just above the rear of the trigger guard using a punch and a small hammer. Pull the trigger assembly downward and outward out of the bottom of the receiver. To remove the bolt and slide assembly, reach into the receiver, lift the rear of the left and right bolt slide, and slide the entire bolt, carrier dog, and action bars forward out through the front opening of the receiver.



Step 4: Deep Cleaning the Barrel and Chamber

Attach the bronze bore brush to your solid brass cleaning rod, saturate it with solvent, and pass it completely through the barrel from the chamber end to the muzzle a dozen times. Pay specialized attention to the forcing cone and the chamber entry point, where plastic wad residue accumulates aggressively. Follow the brushing with clean cotton patches until they emerge completely white, then pass a lightly oiled patch down the bore to inhibit rust.



Step 5: Scrubbing the Receiver and Internal Components

Dip your nylon utility brush into solvent and aggressively scrub the internal receiver tracks, the ejector, and the bolt assembly to strip away carbon fouling and unburnt powder grains. Wipe all parts thoroughly with a dry shop rag to remove suspended debris. Apply a thin, protective film of synthetic gun oil to the action bars, the exterior of the magazine tube, and all high-friction sliding surfaces inside the receiver.



Step 6: Reassembly and Function Testing

Slide the bolt assembly and action bars back into their respective tracks inside the receiver, ensuring the carrier dog is properly aligned. Insert the barrel ring over the magazine tube and seat the barrel fully back into the receiver recess. Thread the magazine cap back onto the tube and tighten it hand-tight. Finally, perform an unloaded function test by cycling the action three times and dry-firing in a safe direction to ensure the trigger and safety mechanisms reset correctly.


REMINGTON 870 BOLT ASSEMBLY W/SLIDE * LW 20 GA OR EXPRESS 20 GA ONLY ...

REMINGTON 870 BOLT ASSEMBLY W/SLIDE * LW 20 GA OR EXPRESS 20 GA ONLY ...

Remington 870 Maintenance Specifications and Material Thresholds



Component Part Material Composition Cleaning Agent Recommendation Lubrication Requirement
Barrel & Bore Carbon Steel / Chrome-Lined Bore Solvent & Bronze Brush Light Film of Gun Oil
Receiver Machined Steel CLP or Mineral-Based Solvent Medium Viscosity Oil
Trigger Assembly Polymer or Steel Housing Non-Chlorinated Degreaser Dry Lube or Drop of Oil on Pins
Magazine Tube Blued Carbon Steel Solvent-Dampened Rag Thin Protective Grease
Stock & Fore-end Hardwood or Synthetic Mild Soap and Water None (Wood Wax Optional)

Common Maintenance Failures and Field Fixes



  • Failure to Extract / Sticky Action:

    • Root Cause: Carbon and plastic build-up inside the chamber or underneath the extractor claw on the bolt face.
    • Actional Fix: Use a dedicated 12-gauge chamber brush attached to a power drill at low RPM with solvent to aggressively scrub the chamber wall, followed by removing the extractor and clearing debris from the spring-loaded claw.
  • Surface Rust Formation on Parkerized Finish:

    • Root Cause: Moisture entrapment or failure to apply a protective oil barrier after handling the firearm with bare hands in humid weather.
    • Actional Fix: Scrub rusted areas with fine 0000 steel wool soaked in gun oil, wipe completely dry, and coat the entire exterior surface with a silicone-treated cloth.
  • Loose Magazine Cap During Rapid Firing:

    • Root Cause: The magazine cap detent spring failing to engage the serrations inside the cap due to dirt or structural fatigue.
    • Actional Fix: Remove the barrel, clean out the detent ball and spring housing located inside the barrel ring, and lubricate the spring to restore positive clicking tension.

Frequently Asked Questions



How often should I clean my Remington 870?

You should perform a standard field strip and cleaning after every 250 to 500 rounds fired. If you hunt in wet, snowy, or coastal environments, clean and oil the shotgun immediately upon returning indoors to prevent flash rusting on the carbon steel receiver and barrel.



Can I use WD-40 to clean and lubricate my Remington 870?

No, you should never use standard WD-40 for long-term firearm maintenance. WD-40 is primarily a water-displacing solvent that dries into a gummy, varnish-like residue over time, which will cause the internal trigger mechanism and action bars to jam. Always use dedicated gun oils and cleaning solvents.



What is the easiest way to remove plastic fouling from the barrel?

Plastic fouling from shotgun wad cups is best removed using a bronze 12-gauge brush soaked in a specialized solvent designed to dissolve plastic, such as Hoppe's Elite or Barnes CR-10. Let the solvent sit in the barrel for ten minutes before scrubbing vigorously with the brush.



Do I need to completely disassemble the trigger group for routine cleaning?

No, factory trigger groups rarely require complete pin-by-pin disassembly for standard maintenance. Simply spray the assembled trigger plate with a non-chlorinated aerosol cleaner, scrub external surfaces with a nylon brush, blow it out with compressed air, and apply a single drop of oil to the hammer and sear pivot points.

Master your shotgun maintenance routine today to guarantee flawless cycling, zero jams, and decades of reliable field performance from your Remington 870.


How to Clean a Remington 870 - The Lodge at AmmoToGo.com

How to Clean a Remington 870 - The Lodge at AmmoToGo.com

Read also: Services at Wallace-Thompson Funeral Home Lewis-Sullivan Chapel