Comprehensive Guide: How To Check Compressor Windings For Electrical Faults

Comprehensive Guide: How To Check Compressor Windings For Electrical Faults

How To Check If Ac Compressor Is Getting Power at Christopher Hurtado blog

Testing compressor windings requires a high-quality digital multimeter to measure resistance between the common, start, and run terminals. By comparing observed values against manufacturer specifications and checking for a short to ground, technicians can definitively diagnose compressor motor failure.


Essential Preparation and Diagnostic Equipment Requirements

Before attempting to test a compressor, ensure the electrical disconnect is pulled and the system is fully de-energized. Confirming zero voltage is the most critical safety step to prevent arc flash or electrocution. Technical precision in this diagnostic procedure relies on isolating the compressor from the start components—capacitors and relays—to prevent false readings or damage to the multimeter.



  • Essential Tools: Digital Multimeter (True RMS preferred) with a minimum 0.1-ohm resolution, insulated screwdrivers, needle-nose pliers, and manufacturer-specific electrical specifications (OEM manual or data plate).
  • Required Prerequisites: Fundamental understanding of single-phase or three-phase motor configuration (C, S, R terminals), proficiency in using Ohmmeters, and Lockout/Tagout (LOTO) certification.
  • Operational Benchmarks: The entire diagnostic process typically requires 15 to 30 minutes. If readings fall outside a 10 percent variance of manufacturer specifications, the motor winding is likely compromised.

Procedural Workflow for Compressor Winding Resistance Testing



Step 1: Secure the System and Access Terminals

Remove the electrical service panel on the compressor unit to expose the terminal block. Disconnect all external wiring, including the power leads and the capacitor leads. Removing these is non-negotiable, as residual charge in a start capacitor or back-feed from other circuit components will skew your resistance readings and potentially ruin your multimeter.



Step 2: Calibrate the Multimeter and Zero the Leads

Set your multimeter to the lowest resistance (Ohms) setting. Before touching the compressor terminals, touch your meter leads together. If the meter does not read 0.0, note the discrepancy (the lead resistance) and subtract this value from your final winding measurements to ensure accuracy.



Step 3: Measure Resistance Between Terminals

Identify the Common (C), Start (S), and Run (R) terminals. You must measure the resistance across three specific pairs: C to S, C to R, and S to R. Record each value carefully.

Warning: Never use a Megohmmeter (Megger) on a hermetic compressor terminal unless you are specifically testing for insulation breakdown at high voltage, as it can damage internal motor components if used incorrectly.



Step 4: Verify the Summation Rule

For a standard single-phase compressor, the resistance of the Start-to-Run (S to R) circuit must equal the sum of the Common-to-Start (C to S) and Common-to-Run (C to R) circuits. If the values do not align within a small margin of error (typically +/- 5 percent), the winding is likely internally damaged or experiencing a high-resistance short.



Step 5: Test for Short to Ground

Set your multimeter to the highest resistance setting or use the continuity/diode test mode. Place one probe on a clean, unpainted piece of copper tubing or the compressor shell, and the other probe on each of the three terminals (C, S, and R). Any reading other than "Open Line" or infinite resistance indicates the motor windings have shorted to the chassis, signifying a catastrophic failure.


how to check 3 phase compressor to ground - Wiring Work

how to check 3 phase compressor to ground - Wiring Work

Technical Parameters for Compressor Winding Evaluation

The following table outlines the expected resistance behavior for a healthy compressor motor versus a failed unit. These metrics assume a standard single-phase hermetic motor.



Measurement Path Normal Operation Reading Failed/Shorted Reading Open/Burned Reading
Common to Start (C-S) Moderate Resistance Near 0 Ohms Infinite (OL)
Common to Run (C-R) Lowest Resistance Near 0 Ohms Infinite (OL)
Start to Run (S-R) Sum of C-S + C-R Near 0 Ohms Infinite (OL)
Any Terminal to Ground Infinite (OL) Low Resistance (< 100k Ohms) N/A

Common Field Failures and Electrical Remedies

Accurate diagnosis requires distinguishing between a failed motor and an external component failure. Follow these protocols when troubleshooting common anomalies:



  • Root Cause: The compressor hums but does not start, and the S-R resistance is infinite.

    • Actionable Fix: The internal overload protector may have tripped, or the start winding is open. Wait 30 minutes for the compressor to cool; if the resistance remains open, the compressor is defective.
  • Root Cause: Meter shows continuity from a terminal to the compressor shell.

    • Actionable Fix: This is a ground fault. Do not attempt to power the compressor. Replace the compressor immediately, as the internal insulation has failed.
  • Root Cause: Terminal readings are erratic or fluctuating wildly.

    • Actionable Fix: Inspect the terminal pins for pitting, corrosion, or arcing. If the pins are loose, the hermetic seal is compromised. Replace the unit, as this is a high-risk failure point.

Frequently Asked Questions



What should I do if my meter shows infinite resistance on all terminals?

If you read infinite resistance (OL) across all terminal combinations, you have likely tripped the internal overload protector, or the internal common connection has burned out. Allow the compressor to cool for at least one hour and re-test; if the readings remain open, the internal motor assembly is dead.



Can I test compressor windings without disconnecting the capacitor?

No. Leaving the capacitor connected creates a parallel circuit that will provide a false resistance reading and potentially cause the multimeter to display incorrect values as the capacitor charges. Always isolate the terminals before taking measurements.



Does a low resistance reading mean the compressor is good?

Not necessarily. While a low resistance (continuity) is expected across windings, extremely low resistance values (near zero) indicate a shorted winding, which will cause the compressor to draw excessive amperage and trip the breaker. Always compare your readings against the manufacturer’s data plate or technical documentation.



Why is the resistance of Start to Run different from the sum of C-S and C-R?

If the S-R resistance does not equal the sum of C-S and C-R, the motor has likely suffered internal damage, such as a partial winding short or localized heating that altered the wire integrity. In most modern hermetic compressors, this discrepancy confirms that the motor is no longer operating within its design specifications and requires replacement.

Consult your HVAC system’s technical service manual for specific resistance values tailored to your compressor’s model number to ensure accurate diagnostics. Contact a licensed professional if your test results indicate a ground fault to prevent potential electrical hazards.


HVAC QUICK COMPRESSOR WINDING CHECK | PDF

HVAC QUICK COMPRESSOR WINDING CHECK | PDF

Read also: Inside the career and legacy of the famous michael reardon