How To Change A Tap Washer: A Step-by-Step Guide For Australian Homes

How To Change A Tap Washer: A Step-by-Step Guide For Australian Homes

How To Change A Hansa Tap Washer at Hazel Barrett blog

Replacing a leaking tap washer is a fundamental plumbing maintenance task that involves isolating the water supply, disassembling the spindle mechanism, and installing a new EPDM or silicone washer of the correct diameter. By following the correct sequence of pressure relief and component seating, homeowners can eliminate persistent dripping and prevent long-term damage to tap seats and pipework.


Pre-Operation Requirements and Tooling

Before commencing any plumbing work, it is essential to prepare your workspace to prevent water damage and ensure the repair is effective. Most Australian taps (jumper valve style) rely on a rubber seal that degrades over time due to mineral buildup, water pressure, and mechanical friction.



  • Essential Equipment:

    • Adjustable spanner or crescent wrench (minimum 250mm).
    • Flat-head and Phillips-head screwdrivers (a multi-bit set is recommended).
    • Replacement tap washers (standard Australian sizes are typically 12mm or 15mm; purchase a variety pack if unsure).
    • Silicone-based plumbing lubricant or tap grease (optional but recommended for longevity).
    • A clean rag or microfiber cloth to protect chrome finishes from wrench scratches.
    • A small container or magnet to hold loose screws and O-rings.
  • Mandatory Prerequisites:

    • Locate the water mains isolation valve (stopcock) for the property, usually found near the front boundary or inside the meter box.
    • Understand that if the leak persists after a washer change, the tap seat itself may require reseating with a specialized reseating tool.
  • Time & Cost Benchmarks:

    • Estimated duration: 15 to 30 minutes for a standard tap.
    • Estimated material cost: Under $10 AUD for a pack of assorted washers.

Procedural Workflow for Washer Replacement

Follow these steps precisely to ensure the integrity of the tap assembly and prevent thread stripping or cross-threading during reassembly.



Step 1: Isolating the Water Supply

Turn off the water mains at the meter. Once the main supply is isolated, open the leaking tap fully to bleed all residual pressure from the pipes. This step is critical; if pressure is not relieved, you may experience a minor spray when removing the spindle.



Step 2: Removing the Tap Handle and Dress Cover

Remove the cover button (the small plastic cap usually marked H or C) using a thin flat-head screwdriver. Once removed, unscrew the handle retaining screw hidden underneath. Pull the tap handle straight up to reveal the spindle assembly. If the handle is stuck due to lime scale, gently tap it from the underside with the handle of your screwdriver to break the seal.



Step 3: Extracting the Spindle Assembly

Use an adjustable spanner to grip the hexagonal nut on the spindle. Turn it anti-clockwise to unscrew the spindle from the tap body. Be mindful of the internal threads; if you feel significant resistance, apply a small amount of penetrating oil and wait five minutes before attempting to rotate again.



Step 4: Replacing the Jumper Valve Washer

The washer (jumper valve) is usually located at the base of the spindle assembly. It may fall out when you remove the spindle, or it may remain inside the tap body. Remove the old washer and inspect it for signs of hardening, tearing, or mineral pitting. Place the new washer onto the spindle, ensuring it is seated firmly.

Pro-Tip: If the tap was leaking for a long time, the tap seat—the metal ring the washer presses against—might be grooved. Run your finger (with caution) or a cotton bud inside the tap body to check for roughness. If the surface feels jagged, you will need a tap reseating tool to grind it smooth, or the new washer will fail prematurely.



Step 5: Lubrication and Reassembly

Apply a small smear of food-grade silicone plumbing grease to the spindle threads and the O-ring of the spindle. This ensures smooth operation and prevents the thread from seizing in the future. Screw the spindle back into the tap body by hand first to avoid cross-threading, then tighten firmly with your spanner. Do not overtighten, as this can crack the tap body or deform the new washer.



Step 6: Testing the Repair

With the tap in the "open" position, slowly turn the water mains back on. Check for any leaks around the base of the spindle. Once the air has cleared from the lines, close the tap firmly and observe the spout for 60 seconds to ensure the drip has ceased.


How to Change the Washer in a Shower Faucet: 7 Easy Steps

How to Change the Washer in a Shower Faucet: 7 Easy Steps

Component Specifications and Material Selection



Component Function Material Standard Replacement Frequency
Jumper Valve Seals water flow EPDM or Synthetic Rubber 2–5 years
Spindle O-Ring Prevents handle leaks Nitrile Rubber As needed
Tap Seat Seating surface Brass (typically) Only if damaged
Lubricant Reduces friction Food-grade Silicone Every service

Common Field Failures and Remediation

Even with a successful installation, specific conditions can cause immediate or delayed failure of the repair.



  • Root Cause: The tap still drips after replacement.

    • Actionable Fix: The brass tap seat is likely pitted or rough. You must use a tap reseating tool to cut a smooth, flat surface back onto the seat, or the new rubber washer will be shredded by the uneven metal.
  • Root Cause: Water leaks from under the tap handle (not the spout).

    • Actionable Fix: This indicates a failed O-ring on the spindle body rather than the jumper valve. Remove the spindle again and replace the small rubber O-ring located on the external shaft of the spindle.
  • Root Cause: The tap handle is difficult to turn.

    • Actionable Fix: You have likely overtightened the spindle nut or failed to lubricate the threads. Back off the spindle nut slightly or remove the spindle to apply additional silicone grease to the threads and the jumper valve stem.

Frequently Asked Questions



How do I know what size washer I need?

Most standard Australian taps use 12mm or 15mm washers. If you are unsure, it is best to take the old washer to a local hardware store to match the physical dimensions against a sizing gauge or existing stock before beginning your repair.



Is it necessary to turn off the main water supply?

Yes, isolating the water supply is mandatory for any plumbing work involving the disassembly of a tap spindle. Failing to do so will result in high-pressure water flooding the area as soon as the spindle is removed from the tap body.



Can I fix a dripping tap without replacing the washer?

In rare cases, the washer may just be dislodged or obstructed by sediment, but in 99% of residential cases, the rubber has physically degraded. Replacing the washer is an inexpensive and permanent fix that is significantly more reliable than attempting to clean a damaged seal.



What should I do if the tap is still leaking after reseating the seat?

If the seat is smooth and the washer is new but the leak persists, the spindle itself might be worn, or there may be debris lodged further down the line. Inspect the spindle threads for wear and consider replacing the entire spindle assembly if the thread appears stripped or the stem is bent.

Expert Plumbing Support

If you encounter complex issues such as corroded pipework, persistent leaks behind the wall, or seized spindle assemblies that resist removal, it is time to consult a licensed plumber. Professional intervention protects your property from potential water damage and ensures compliance with Australian plumbing standards.


How To Change A Tap Washer | Bathroom Mountain

How To Change A Tap Washer | Bathroom Mountain

Read also: Artificial intelligence will enhance myinstins sound generation soon