How To Change Draw Weight On Compound Bow: A Complete Step-by-Step Tuning Guide
To change the draw weight on a compound bow, rotate the limb bolts clockwise to increase weight or counterclockwise to decrease weight, ensuring both bolts are adjusted in equal, alternating increments. Never exceed the manufacturer's maximum recommended turns—typically 4 to 10 turns from bottomed out—to prevent catastrophic limb pocket failure. Always verify your adjustments using a calibrated digital bow scale and measure tiller height to guarantee balanced limb performance.
Adjusting the draw weight of your compound bow is a fundamental aspect of bow tuning that directly impacts arrow velocity, kinetic energy, and your physical shooting form. Whether you are building up your pulling strength, fine-tuning your setup for a specific hunting season, or backing off the weight for an extended indoor target session, performing this task correctly ensures both your safety and the longevity of your equipment.
Essential Tools and Safety Parameters Before Adjusting Your Bow
Modifying draw weight involves manipulating high-tension components. Before placing a wrench on your bow's limb bolts, you must understand your specific bow design and assemble the correct tools. Modern compound bows utilize either pivoting or rigid limb pocket systems, and adjusting them requires precision to avoid damaging the thread engagement within the aluminum riser.
Required Gear, Safety Standards, and Benchmarks
- Handheld Digital Bow Scale: Essential for obtaining real-world peak draw weight measurements rather than relying solely on manual turn estimates.
- High-Quality Hex Keys (Allen Wrenches): Standard SAE sizes (most commonly 3/16 inch or 7/32 inch) made of hardened steel to prevent stripping the limb bolt sockets.
- Tiller Ruler or Tape Measure: Used to measure the distance from the string to the limb-riser intersection to ensure even limb loading.
- Limb Pocket Lubricant (Optional): High-grade white lithium grease or specialized bow grease for older bows prone to pocket chatter.
- Prerequisite Knowledge: Locate your bow’s user manual to identify the maximum allowable limb bolt turns (typically 4 to 6 turns for high-performance hunting bows, and up to 10 or more for highly adjustable youth/infinite-draw bows).
- Project Duration: 15 to 20 minutes.
- Estimated Budget: $20 to $60 (primarily for a reliable digital scale and quality hex set).
Step-by-Step Guide to Safely Adjusting Compound Bow Draw Weight
Follow these step-by-step procedures to alter your draw weight safely. Skipping any of these preparation or execution phases can lead to structural limb failure, stripped riser threads, or violent bow derailment.
Step 1: Establish Your Baseline Draw Weight and Tiller
Before making any adjustments, you must know your starting point. Hang your bow by its d-loop or riser hook on a calibrated digital scale and pull down smoothly to record the current peak draw weight. Write this number down. Next, measure the tiller. Use your tape measure to find the perpendicular distance from the bowstring to the point where the upper limb meets the riser. Repeat this measurement for the lower limb. These two numbers should be identical (or within 1/16 of an inch of each other) to ensure the cams track properly during the draw cycle.
Step 2: Locate and Inspect the Limb Pocket Locking Screws
Many modern compound bows feature small locking screws located on the sides or rear of the limb pockets. These locking screws pinch the pocket to prevent the main limb bolts from vibrating loose over time.
Warning: You must loosen these pocket locks before attempting to turn the main limb bolts. Failure to do so will strip the locking threads, damage the limb pocket, or bind the main bolt, permanently seizing the adjustment mechanism. Using a smaller hex wrench, back these lock screws out 1 to 2 full turns. Do not remove them entirely; they only need to be loose enough to allow the limb pocket to pivot freely.
Step 3: Bottom Out the Limb Bolts (For Baseline Calibration)
To ensure both limbs are perfectly synchronized, it is best practice to "bottom out" the bow first. Insert your primary hex wrench into the top limb bolt and turn it clockwise until it is snug. Do not over-tighten or crank down hard on the bolt, as this can crush the limb dampeners or deform the riser threads. Repeat this process for the bottom limb bolt. Once both bolts are fully bottomed out, your bow is set to its maximum rated manufacturer weight (e.g., exactly 70 pounds on a 60–70 lb bow).
Step 4: Rotate the Limb Bolts in Equal, Alternating Increments
If you want to decrease your draw weight from the maximum setting, you will turn the bolts counterclockwise. If you are starting from a backed-off position and want to increase the weight, you will turn them clockwise.
Pro-Tip: Never adjust one limb bolt more than two full turns at a time before moving to the other limb. Adjusting one bolt completely while the other remains tight puts immense asymmetric twisting force on the riser, cams, and limbs, which can crack the fiberglass or warp the cam axles. Turn the top limb bolt counterclockwise exactly one full 360-degree rotation. Move to the bottom limb bolt and turn it counterclockwise exactly one full 360-degree rotation. Repeat this alternating process until you reach your desired weight. Count your turns carefully and record them.
Step 5: Verify Safe Thread Engagement and Retighten Pocket Locks
If you are backing down the weight significantly, check the manufacturer's maximum turn limits. For example, if your bow has a maximum limit of 6 turns, and you have completed 5 turns, stop. Ensure you can see the limb bolt threads through the inspection window on the side of the riser if your bow model features one. This guarantees there is still a safe amount of thread engagement (typically a minimum of 1/2 inch) holding the limbs to the riser. Once your turns are completed, retighten the pocket locking screws loosened in Step 2 to lock the assembly in place.
Step 6: Verify Tiller and Test the Final Draw Weight
Measure the upper and lower tiller once more. They should match your initial measurements. If one side is slightly off, make a micro-adjustment (1/8 to 1/4 of a turn) to the corresponding limb bolt to bring them into balance. Finally, draw the bow on your digital scale to verify the new peak draw weight. Execute a few practice shots into a safe target at close range to ensure there are no strange vibrations, creaks, or alignment issues within the limb pockets.
Dual Use Compound Bow 50-70lbs Adjustable Draw Weight Archery Kit - AME ...
Limb Bolt Adjustment Specifications Across Major Bow Brands
The table below outlines general adjustment parameters for major bow manufacturing archetypes. Please refer to your specific owner's manual, as models within the same brand can vary depending on the limb pocket engineering.
| Bow Design Archetype | Average Weight Change Per Full Turn | Max Safe Turns from Bottomed Out | Pocket Locking Style | Minimum Thread Engagement |
|---|---|---|---|---|
| Hoyt (Split Limb / ZTR Pocket) | 2.0 to 2.5 lbs | 8 Turns | Side Locking Screws | 0.500 Inches |
| Mathews (Sherwood / Switchweight) | 2.5 to 3.0 lbs | 5 Turns | No Lock (Tension Fit) | 0.625 Inches |
| Bowtech (Overdrive / DeadLock) | 2.0 to 3.0 lbs | 10 Turns | Pocket Lock Screws | 0.500 Inches |
| Bear Archery (Highly Adjustable Youth) | 3.0 to 4.0 lbs | 12 Turns | No Lock | 0.750 Inches |
| Prime (Inline / Parallel Cam) | 2.0 to 2.5 lbs | 6 Turns | Double Side Locks | 0.550 Inches |
Common Adjustment Failures and Professional Field Fixes
Even experienced archers can run into mechanical issues when adjusting draw weight. Below are the most common failures encountered during this tuning process, along with their root causes and structural remedies.
- Failure Scenario: The limb bolt feels completely seized or extremely difficult to turn.
- Root Cause: The pocket locking screws are still tightened down, or the aluminum-on-steel threads have galling due to a lack of anti-seize lubricant.
- Actionable Fix: Stop turning immediately to prevent shearing the bolt head. Inspect the sides of the riser for recessed hex locking screws and loosen them. If the bolt is still seized, apply a small drop of penetrating oil to the threads, let it sit for ten minutes, and try again slowly.
- Failure Scenario: The bow emits a loud popping or creaking sound during the draw cycle after adjustment.
- Root Cause: The limb pockets are dry, causing the fiberglass limbs to bind and release dryly against the pivoting plastic/metal pocket liners as the bow flexes.
- Actionable Fix: Back the limb bolts out to their safest maximum limit (or compress the bow in a press), and apply a thin layer of white lithium grease or silicone lubricant between the limb base and the pocket housing.
- Failure Scenario: The bow feels erratic, unstable, or paper-tunes with a persistent vertical tear.
- Root Cause: Out-of-sync tiller caused by unevenly turned limb bolts, which places more stress on one limb and alters the cam timing and nocking point travel.
- Actionable Fix: Bottom out both limb bolts to reset the bow to zero. Re-measure the tiller on both ends, and back them out again, making sure to use a precise paint marker mark on your hex wrench to count exact 360-degree revolutions on both limbs.
Frequently Asked Questions
Does changing my draw weight affect my draw length or cam timing?
Modifying your draw weight changes the physical geometry of the bow. Decreasing the draw weight relaxes the limbs, which slightly increases the axle-to-axle measurement and can lengthen your draw length by up to 1/4 of an inch. It can also cause minor shifts in cam timing and your peep sight alignment, requiring you to re-tune your arrow rest and peep height.
Can I adjust my compound bow's draw weight without using a bow press?
Yes, you do not need a bow press to change the draw weight using the limb bolts. The limb bolts are engineered to handle the load of the limbs throughout their designated adjustment range. However, you must never back the bolts out beyond the manufacturer’s recommended turn limit, or the limbs will violently detach from the riser.
What happens if I turn one limb bolt more than the other?
Turning one limb bolt more than the other creates an uneven tiller, which tilts the limb pockets relative to the riser. This causes uneven limb stress, poor cam synchronization, vertical nock travel issues, and increased noise and vibration during the shot. Always keep the upper and lower limb adjustments identical.
How do I know if my bow limb bolts are bottomed out?
To bottom out your bow, turn the limb bolts clockwise until you meet firm resistance. Do not force or over-tighten the bolt once it stops, as this can crush the limb pocket spacers or strip the threads inside the riser. Once the bolt stops turning naturally under moderate hand pressure, it is fully bottomed out.
Optimize Your Archery Gear for Maximum Precision
Properly tuning your bow's draw weight is the first step toward achieving tighter groups and a more comfortable shooting experience. If you are ready to take your accuracy to the next level, pair your perfectly weighted bow with high-performance arrows and professional tuning accessories designed for absolute field consistency.