Installing Catnic Lintels: A Professional Guide For Structural Load-Bearing Openings

Installing Catnic Lintels: A Professional Guide For Structural Load-Bearing Openings

CBP110/100 Extreme Load Cavity Wall Beam Lintels | Lintels | Catnic

Installing Catnic steel lintels requires precise alignment, a minimum end bearing of 150mm on each side, and strict adherence to mortar leveling standards to ensure long-term structural integrity. This guide covers the end-to-end installation sequence, from initial wall preparation to the final bedding process, compliant with building regulations for masonry support.


Essential Preparation and Technical Requirements

Successful lintel installation relies on accurate site preparation and the availability of the correct load-bearing specifications. Before placing the lintel, verify that the wall masonry is cured enough to support the dead load and that the structural opening matches the lintel length specifications precisely.



  • Essential Tools: Spirit level (minimum 1200mm), heavy-duty mortar trowel, lump hammer, bolster chisel, pointing trowel, and mechanical lifting aid for heavy-duty spans.
  • Required Materials: Proprietary lintels specified for your wall type (cavity, box, or channel), Grade M4 mortar mix, damp-proof course (DPC) material, and galvanized wall ties.
  • Safety Gear: Steel-toe boots, protective gloves, safety glasses, and hard hat for overhead work.
  • Key Benchmarks: Ensure all lintels are marked with the "front" indication and that the specified end bearing (usually 150mm) is maintained on each side of the aperture. Always check the manufacturer’s load tables to confirm the selected lintel gauge matches your specific floor or roof load.

The Professional Installation Workflow



Step 1: Preparing the Masonry Supports

Clear the aperture of any debris, loose brickwork, or mortar droppings. Ensure the brickwork or blockwork where the lintel will sit is level and plumb. If the support surface is uneven, lay a thin bed of mortar to create a perfectly horizontal plane. The lintel must sit on a solid, load-bearing surface, not on loose insulation or unstable brick fragments.



Step 2: Applying the Damp-Proof Course (DPC)

In cavity wall construction, a continuous DPC is mandatory. Position the DPC on the inner leaf, extending it a minimum of 150mm beyond each end of the lintel. The DPC must be tucked into the cavity at least 25mm to prevent water ingress from crossing into the interior leaf. Ensure the DPC does not sag, as this can create a moisture bridge.



Step 3: Bedding the Lintel

Apply a full bed of mortar to the support masonry. Place the lintel into position, ensuring it is perfectly level both longitudinally and across its width. If the lintel is a cavity type, ensure the inner and outer flanges are correctly oriented. Use a spirit level to check for any slope; an unlevel lintel will cause uneven stress distribution and potential cracking in the masonry above.



Step 4: Securing the Lintel and Masonry Loading

Once positioned, build up the masonry to the lintel, ensuring mortar is fully packed under the ends of the lintel. For the first two courses of masonry above the lintel, use a stronger mortar mix or include reinforcement mesh if specified by your structural engineer. Never apply point loads (such as floor joists or roof trusses) directly onto the lintel until the mortar has reached its initial set, typically after 24 hours.



Step 5: Cavity Insulation and Weep Holes

Install the required cavity insulation behind the outer flange to minimize thermal bridging. Ensure that weep holes are installed at intervals no greater than 900mm along the length of the external flange to allow for proper moisture drainage. These weep holes must remain clear of mortar during the subsequent brickwork phases.


Buy Catnic L Shaped Angle Steel Lintels | Next Day Delivery Available

Buy Catnic L Shaped Angle Steel Lintels | Next Day Delivery Available

Lintel Specifications and Selection Matrix



Lintel Type Typical Application Minimum Bearing Key Performance Metric
Standard Cavity External wall openings 150mm Thermal bridging resistance
Box Lintel Heavy load / Wide spans 150mm High vertical load capacity
Channel Lintel Internal partition walls 100mm Lightweight handling
EWI Lintel External wall insulation 150mm Thermal envelope continuity

Troubleshooting Common Site Failures



  • Uneven Settlement: Occurs when the support masonry is not properly cured or leveled before lintel placement. Fix this by ensuring all bearing surfaces are verified with a spirit level and allowed to set for at least 24 hours before the lintel load is applied.
  • Moisture Bridging: Caused by incorrect DPC positioning or mortar droppings inside the cavity. Always keep the cavity clear of debris during construction and ensure the DPC is positioned with a slight downward slope toward the outer leaf.
  • Excessive Deflection: Often the result of selecting an under-specced lintel for the anticipated structural load. Verify the structural engineer’s calculations against the specific lintel load table; if deflection exceeds 1/500th of the span, the lintel must be replaced with a higher-gauge alternative.

Frequently Asked Questions



How much bearing is required for a standard Catnic lintel?

The standard requirement is a minimum of 150mm bearing at each end of the lintel for masonry openings. Always consult the specific project structural drawings, as wider spans or heavier loads may necessitate extended bearing lengths to properly distribute the force.



Can I cut a Catnic lintel to size on-site?

Generally, you should not cut standard lintels as this compromises the galvanization and structural integrity. If a specific length is required, order the precise length from the manufacturer; if a slight adjustment is unavoidable, you must apply a cold galvanizing spray to all exposed steel surfaces immediately after cutting.



Why do I need to include weep holes?

Weep holes are essential to allow water that penetrates the outer leaf or condensation within the cavity to escape. Without them, moisture will accumulate on the lintel, leading to corrosion and potential water ingress through the inner wall.



What is the purpose of the thermal break in a cavity lintel?

The thermal break prevents cold from the exterior leaf from transferring to the inner leaf. This prevents condensation and black mold growth on internal plaster surfaces, ensuring the wall remains energy efficient and compliant with current building regulations.

Ensure Structural Integrity with Industry-Grade Components

Properly installing your steel lintels is the foundation of a durable and weather-tight building envelope. Consult with a qualified structural engineer for specific load-bearing requirements and ensure all materials meet the latest national building codes for safety and performance.


TH190/100 Heavy Duty Steel Lintels | Thermally Broken | Lintels | Catnic

TH190/100 Heavy Duty Steel Lintels | Thermally Broken | Lintels | Catnic

Read also: Bx4 and Bx4A Bus Timetables: MTA Bronx Service Schedules