How To Backflush A Hayward Pool Filter: Complete Step-by-Step Guide

How To Backflush A Hayward Pool Filter: Complete Step-by-Step Guide

Hayward ProSeries Sand Filters — Sand Filter Top Mounts 18"-31"

Backflushing a Hayward pool filter reverses the internal water flow to flush out trapped dirt, debris, and contaminants through the waste line. You should perform this maintenance procedure whenever the pressure gauge reads 8 to 10 PSI above your clean starting baseline, or approximately every two to four weeks depending on pool usage and environmental factors.


Pre-Operation & Equipment Checklist

Maintaining a clean Hayward pool filter requires proper preparation and an understanding of your system's baseline operating parameters. Before turning any valves, ensure your workspace is clear and you have verified the structural integrity of your multiport or push-pull valve.



  • Essential Gear and Tools: Backwash hose (reinforced vinyl or lay-flat), hose clamps, replacement O-rings or multiport spider gasket if leaks are present, and safety glasses.
  • Mandatory Prerequisite Knowledge: Record your clean filter operating PSI immediately after a thorough cleaning. Know the exact location of your waste discharge area to prevent local flooding or chemical runoff violations.
  • Estimated Time and Budget: The physical backflush process takes approximately 10 to 15 minutes. Budget between zero dollars for standard maintenance and fifty dollars if replacing worn multiport valve components.

Step-by-Step Hayward Filter Backflush Procedure

Executing a safe and effective backflush requires strict adherence to pump shutdown protocols to prevent severe pressure spikes and internal equipment damage.



Step 1: Power Down the Filtration System

Turn off your pool pump completely at the automation panel or breaker box before touching any manual valves. Never rotate a Hayward multiport valve handle while the pump motor is actively running, as this places extreme mechanical stress on the internal diverter gasket and can deform or shear the sealing components instantly.



Step 2: Connect and Secure the Backwash Hose

Roll out your flexible backwash hose and attach it securely to the waste or backwash port located on the side of your Hayward multiport valve. Fasten the connection tightly using a metal hose clamp to prevent the high-velocity discharge water from blowing the hose off during operation. Unroll the downstream end of the hose and direct it safely toward a legal drainage area, street gutter, or dry well in compliance with local municipal codes.



Step 3: Configure the Valve for Backflushing

Push down firmly on the Hayward multiport valve handle and rotate it clockwise until the indicator pointer locks securely into the Backwash position. If your system utilizes a Hayward push-pull (slide) valve instead of a multiport, push or pull the handle to the open backwash position depending on your specific model instructions.

Warning: Always depress the multiport valve handle fully before turning it. Forcing a partially depressed handle will permanently destroy the internal Teflon-backed spider gasket and lead to continuous water loss down the waste line.



Step 4: Run the Backwash Cycle

Turn the pool pump back on and let it run for approximately 2 minutes, or until the water flowing through the clear sight glass on the waste port runs completely clean and transparent. Monitor the discharge stream and ensure your drainage area is absorbing the volume without overflowing into neighboring properties.



Step 5: Execute the Rinse Cycle

Turn the pool pump off again at the breaker. Depress and rotate the Hayward multiport valve handle to the Rinse position, then turn the pump back on for 30 to 45 seconds. This critical intermediate step settles the sand bed or cleans the filter elements, preventing residual debris from blowing back into your clean swimming pool when you resume normal filtration.



Step 6: Return to Normal Filtration Mode

Turn off the pool pump for a final time. Depress and turn the multiport valve handle to the Filter position. Remove the temporary backwash hose if desired, and turn your pool pump back on. Immediately inspect the pressure gauge on top of the Hayward filter tank to confirm it has returned to your clean baseline PSI reading.


How To Replace Hayward DE Filter Grids - INYOPools.com

How To Replace Hayward DE Filter Grids - INYOPools.com

Hayward Filter Operating Parameters & Comparison

Understanding the performance thresholds of your specific Hayward filter media type ensures optimal water clarity and prevents premature equipment wear.



Filter Media Type Typical Cleaning PSI Threshold Average Filtration Efficiency Recommended Replacement Interval
Hayward Sand Filter (Matrix/ProGrid) 8 - 10 PSI above clean baseline 20 to 40 microns Sand: 5 to 7 years
Hayward DE Filter (ProGrid/PerFecFlo) 8 - 10 PSI above clean baseline 3 to 5 microns Grids: 3 to 5 years
Hayward Cartridge Filter (SwimClear) 8 - 10 PSI above clean baseline 10 to 15 microns Cartridges: 1 to 3 years

Troubleshooting Common Backflush Complications

Even with careful execution, pool filtration systems occasionally present operational anomalies that require immediate technical intervention.



  • Root Cause (Cloudy water returns to pool immediately after backflushing): The internal lateral assembly or standpipe in a sand filter has cracked, or a DE grid has ruptured, allowing media to bypass the filter and blow back into the pool return lines.

    • Actionable Fix: Turn off the system immediately, inspect the internal tank components, replace damaged laterals or torn filter grids, and vacuum the settled media from the pool floor.
  • Root Cause (Water constantly trickles out of the waste port during normal filtration): The internal Hayward multiport spider gasket has dislodged, worn out, or accumulated debris under the sealing surfaces.

    • Actionable Fix: Disassemble the multiport valve top cover, clean the sealing surfaces thoroughly, and replace the spider gasket with genuine Hayward OEM replacement parts.
  • Root Cause (Filter pressure remains high immediately after a complete backflush): Calcification, body oils, or algae have chemically blinded the sand bed or filter elements, which backflushing water velocity cannot break apart.

    • Actionable Fix: Apply a specialized chemical filter cleaner or degreaser directly to the filter media, allow it to soak according to package directions, and perform an extended manual wash cycle.

Frequently Asked Questions



How often should I backflush my Hayward pool filter?

You should backflush your Hayward filter when the pressure gauge rises 8 to 10 pounds per square inch (PSI) above your initial clean starting pressure. Under normal summer operating conditions with heavy bather loads, this typically equates to once every two to three weeks.



Can I backflush a Hayward cartridge filter?

No, Hayward cartridge filters (such as the SwimClear series) cannot be backflushed because they do not have a multiport valve or a waste discharge port. Instead, you must remove the polyester cartridges from the tank shell and wash them down manually using a garden hose with a nozzle attachment.



Why is my Hayward filter pressure high even after backflushing?

High pressure immediately following a backflush usually indicates chemical scaling, organic buildup, or oil contamination coating the filter media. You will need to treat the filter with a specialized commercial filter cleaner or acid wash to dissolve the stubborn binding agents.



Where should I direct the backwash wastewater?

You must direct the backwash wastewater to a municipal storm sewer inlet, a sanitary cleanout on your property, or a compliant dry well according to local environmental regulations. Avoid discharging chlorinated pool water directly onto sensitive landscaping or unprotected neighboring yards.

Keep your pool crystal clear and running at peak hydraulic efficiency by mastering routine Hayward filter maintenance today.


Hayward Pro Series Sand Filter 18 in Above-Ground Pool System - Walmart.com

Hayward Pro Series Sand Filter 18 in Above-Ground Pool System - Walmart.com

Read also: i will cherish your love always becomes the top wedding vow choice